Question about Kenwood KR-V5580

Open Question

Kenwood receiver KRV-5570D sound and display switches / turns off

I have an Kenwood KRV 5570D receiver, and since several months problems are increasing.

Sometimes during operation i hear some scratch noise and the speakers are disabled and out of function.
Sometimes it switches from normal operation to loud noise (like a unprecise set radio channel).
Often I hear repeating clicking noise, display is changing (speakers on / off), sometimes it displays 96khz and the speakers are off.

The problems are independent from the input channel.

I have changed the thermal conduction paste between the heat sink and the electronic devices, I also have reset the microcontroller.... no effect.

Is there any chance to repair the receiver, or is everything lost?

Thank you!

Posted by on


4 Suggested Answers

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

  • 4234 Answers

SOURCE: Kenwood:1090VR Cracking sound from front speakers

There are poor solder connections somewhere on the board. Usually these are at the voltage regulators where there can be some heat. Look for 3-legged transistors attached to small metal heatsinks, If you can solder, resolder the pins on those parts. Also look for any connections that appear to be grasiny or have rings and resolder them too.

Keep us posted.

Posted on Feb 06, 2009

  • 2047 Answers

SOURCE: kenwood vr6050 receiver sudden loud static or

Kenwood sound units are probably market leaders in most parts of the world because of the durability and high standard of their products. When loud screeching sounds and static is are heard on sound systems in most cases it is as a result of poor wire connections to the speakers. Check the wires to the speakers most likely the screeching and static is coming from those.
Also static could also be caused by mobile devices being close to the receiver. Mobile devices such as internet modems and mobile phones as well as radio transmitting devices could cause static and screeching.
Hope this solution has been helpful?

Posted on Jan 08, 2011

  • 1 Answer

SOURCE: I own a kenwood KR-A4060 receiver/amp and i can

I have exactly same problem. After inspection it looks like 2 capacitors are burned, C13 and C14. As soon as I find schematics I ll post the values.

Posted on Feb 18, 2011

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

I have a Kenwood audio video stereo receiver model number KRV 7080 where are the fuses located I had a power surge since then it doesn't come on

take it in for a diagnostic check as power surges bypass fuses and do damage to critical electronic items like the CPU unit
with modern communication equipment it is essential that quality surge protectors are in the power cord wire

Feb 28, 2016 | Kenwood Audio Players & Recorders

1 Answer

Hi . I have a Kenwood receiver V-3080 that on start up it comes on for a few sec. the turns off like you switched it off then after several time it stays on without any further problems.

The wiring of a speaker has back feed to a safety shut off because a wire is touching or the polarity has been switched. The volume may be turned up to high to and will cause it to do the same. It is an overload feature, so that you don't blow your speakers with a 100 watts of power surging to it. Changing positive to negitive of the speakerswire to speaker may help.

Dec 01, 2010 | Kenwood VR-3080

1 Answer

Kenwwod VR-615 - display disappears

Its becuase it is dirty inside, Unplug it. Take the case off of it. Get sum compressed air from a computer store or Walmart. Like 10 dollars. And just blow the whole thing out with that canned air. do it ever 3 months.. It should fix the problem for life!(:

Jan 30, 2010 | Kenwood VR615 Receiver

1 Answer

How to hook a powered subwoofer to a kenwood krv-6080 receiver?

Hi tre030

What is the make and model of the Sub you are connecting?


Jul 13, 2008 | Kenwood Audio Players & Recorders

Not finding what you are looking for?
Kenwood KR-V5580 Logo

Related Topics:

313 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kenwood Audio Players & Recorders Experts


Level 3 Expert

5515 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17130 Answers

Don Hart

Level 2 Expert

108 Answers

Are you a Kenwood Audio Player and Recorder Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides