Question about Pool & Spa

1 Answer

I need an impeller replacement for my pool filter

I have been looking for the impeller replacement for about a month now. No one can seem to help me. It is for the Krstal Clear filer Model #635. It came with the Intex Easy Set Model 56904/E 18 ft x 4 ft above the ground pool purchased at Walmart.

Can someone please help???!!!!!!!!!!

Melissa
NY

Posted by on

1 Answer

Go back to the distributor! This items arn't sold to the public yet.

Posted on Sep 04, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

New pool pump motor is rattling


This really sounds like a motor going out. I would take it to a motor shop and have them check the bearings.

US Parts Center

Apr 07, 2014 | AO Smith Pool & Spa

1 Answer

Low flow rate


You probably have debris clogged in the impeller. The pump has to be opened to clean or repair the impeller.

Apr 12, 2013 | Hayward C550 Swimming Pool Filter System...

1 Answer

Our centurion pool pump motor Model B128 replaced less than 1 year ago. Pool company has to replace the impeller twice. Is this common? I believe the pool co sold and installed a used pump instead


Broken impellers generally are not caused by the pump's motor. Impellers usually fail due to back pressure from the filter when the pump shuts off. Air in the filter is compressed while the motor runs, on your pump 12-15 psi. or a bit higher.

When the motor shuts off that compressed air forces water back to the pump, sometimes with enough force to loosen (or completely throw off) the impeller. If the impeller is loose when the pump starts up again it will instantly re-thread the impeller and strip out the threads.

Check to see if you have a suction leak. After the pump has turned on, bleed the air out from the air relief valve on top of the filter. After the pump has run for a while open the air relief valve and see if air comes out. There should be no air, or just a little.

I have seen this back pressure strong enough to blow the skimmer basket up onto the deck.

What make and model of pump and filter do you have?

Feb 22, 2013 | Pool & Spa

3 Answers

Impeller in intex model 635 broken where can I buy replacement part?


A late answer but it might help future Intex impleller sufferers... they do not sell replacement parts and you won't find any impellers sold separately anywhere on the planet. I've had 1 Intex pool and 3 Intex filter pumps in 3 years. Last week the 3rd pump's impeller broke as well. I shan't buy their products again.

Jun 21, 2012 | Intex Krystal Clear Model 635 Pool Filter...

1 Answer

Pentair Whisper Flow 2hp pump appears to not **** as much water as before. Filter basket recently broke and allowed small leaves to get sucked up by the motor. Could this be the reason for the loss of...


Yes, If the debris you speak of got past the filter basket, it can clog the impeller. If the impeller is clogged, it wont pump water. Simply remove the 6 bolts on the pump end, then remove the diffuser with a 3/32 hex wrench, then clean the impeller. Its very easy, and very important that this get done every 6 months in an outdoor pool with trees surrounding it.

Also, the filter basket should last a long time, if this is breaking on you, make sure your water chemistry is in check. Agressive water can cause lots of damage and cost lots of money.

If you still have bad flow after this fix, replace the shaft seal.

Mar 29, 2011 | Pentair WhisperFlo 2HP Up Rated In Ground...

1 Answer

Pump not taking prime. I have a lot of pine leaves or nettles some of which may have got past the strainer. after it took prime it did not seem to have good flow,.


This is indictive of a clogged impeller or blown shaft seal or possibly both.
To clean out the impeller, simply removing the 8 securing bolt that hold the wet end against the seal plate and motor housing. Then remove the diffuser assembley. You should now have access to the impeller. Remove any debris from inside the impeller and impeller cage.
Reassemble , fill with water, and try to reprime.
If prime still fails, take apart again and remove impeller to replace the shaft seal.
Note:
1. Make sure the filter connected to this pump is clean and not causing the problem before following these instructions.
2. Here is the link to the exploded parts diagram for easy reference to part names. It is also good to look at previous to dissassembley so that you have a good understanding of what is where.

Nov 11, 2010 | Jandy Stealth 2 HP UR Pool Pump SHPM2.0...

1 Answer

Stopped running


I would start by looking at the impeller to make sure that it is not jammed. With most of these pool filters, they are not designed for long term use. They are mass produced and not very well made because they are usually used with inflatable/temporary pools. You are probably going to have to replace the filter, unfortunately.

Jul 07, 2009 | Intex Krystal Clear Model 635 Pool Filter...

1 Answer

My pump pressure is 10psi i cleaned the de filters they seem fine i have good floe out of my jets but when i hook the pool cleaner up pressure drops to almost nothing. could my impeller be the problem


The pressure you are reading is the pressure in the filter tank as water is pumped though it. When the filter is freshly charged, 9 PSI is a good pressure.

As the filter removes particles from the water the filter gets "dirty" -- it takes more pressure to push the water through it thus raising the PSI.

I think you are viewing this in reverse. Low filter pressure is "good" (as long as it stays above 8 PSI) -- as the filter cleans the water the PSI will increase -- when it gets to 15-20 PSI it needs to be back-washed and recharged.

The pressure drops when the pool cleaner is connected because pool cleaners always pull in air (in varying amounts) because of all the hose connections. This causes your filter/tank pressure to drop.

May 25, 2009 | Hayward 3/4hp Super Pump Inground Pool...

1 Answer

Do i have the right size pump for my 10,000 +/- inground pool


Bruce,
the cartridge element system you have is designed to be used for at least two seasons before needing to replace the elements. You are correct thinking that the pressure going through the filter is causing the problems with the cleaner.
if you take the elements out of the filter and see if cleaner works that will show you whether or not it is time to change the filter elements. That filter is very expensive to replace. cheaper to just change the elements.

Mar 01, 2009 | Pentair 1.0 Hp Whisperflo Pump

Not finding what you are looking for?
Pool & Spa Logo

Related Topics:

158 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pool & Spa Experts

Jay Finke
Jay Finke

Level 3 Expert

1338 Answers

Bill Jordan

Level 2 Expert

372 Answers

David Spradling
David Spradling

Level 3 Expert

4206 Answers

Are you a Pool and Spa Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...