Question about Frigidaire ATF6000ES Front Load Washer

Open Question

Removing outer seal of frigidaire front loader washer

Show do I remove the outer seal to access the lock

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
Coldcut
  • 1554 Answers

SOURCE: Frigidaire FWTr445rfs1 front loader - door closed but buzzes during washing

by the way it too fixya over 14 hrs to relay that message

Posted on Apr 16, 2008

Ad
  • 1 Answer

SOURCE: Front Loader Frigidaire will not drain model no. LTF530FSO

check to make sure all hoses are not clogged - our washer hose before the pump was clogged due to washing a rug that had deteriorating rubber backing - would not drain until I flushed out the hose that goes from the tub t the pump.

Posted on May 01, 2008

MNfisherman
  • 11896 Answers

SOURCE: Need to remove the front panel of front load washer

you will have to remove the rear panel in order to remove the front panel. The bolt and clamp are inside the front panel.

Posted on Jul 09, 2009

  • 1 Answer

SOURCE: REPLACE BELT

Hi there ,
how do I get the belt around the drum ? do I have to take the whole back panel off the dryer ?
Don

Posted on Jan 16, 2010

allbrands
  • 600 Answers

SOURCE: How do you remove the

hello, just remove the two screws in the lower bottom corners and push the front panel downward. please rate me it helps....thank you.

Posted on Jun 07, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

We have a Frigidaire "Affinity" front loader it is leaving a puddle on the floor when we use it. I assume the rubber ring is bad has anyone changed it themselves? Is it a hard fix?


Are you sure it's the door seal? If it is they are normally just held in place with 2 metal rings, 1 at the edge of the seal at the door opening and one at the outer drum. Once you remove the front ring from the door opening you can gain access to the one at the drum. Removing the lid of the machine will also help and give you a bit more light.
Anyone with a bit of DIY know how should be able to replace it, an hour tops for a beginner.

Dec 29, 2012 | Frigidaire ATF6000ES Front Load Washer

1 Answer

I have a frigidaire affinity front loader washer that the final spin cycle won't work on. The rest of the wash cycle is fine and the basket spins for the other cycles just not the spin cycle. It is also...


There is an auxiliary switch in the door lock and switch assembly that is activated at the end of the wash cycle for the machine to advance to the spin cycle. This is a safety feature to prevent the door from opening during the spin cycle and the machine will not spin unless the switch is activated. The machine works except advancing to the spin cycle and this signifies that the auxiliary switch cannot be activated and the door lock and switch assembly is faulty. Replaced the door lock and switch assembly (part #131763202) to address the issue.

Disconnect power to the machine. Open the washer door then look for the retaining hoop securing the door seal around the lip of the door opening. Stretch the retainer spring of the door seal retaining hoop then remove it.
1df5293.jpg

Carefully peel off part of the door seal from the lip of the door opening near the door lock and switch assembly. Remove enough of the door seal to gain access to the door lock and switch assembly.
3e820a8.jpg

Remove the screws securing the door lock and switch assembly to the front panel. Once the screws are removed, lift the door lock and switch assembly then pull it away from the front panel.
1a4b866.jpg

Take the door lock and switch assembly out of the machine. Disconnect the electrical connections then connect it to the new door lock and switch assembly.
febd08e.jpg

Put the new door lock and switch assembly back into position in the front panel and secure it with the securing screws.

Properly put the eased part of the door seal back over the lip of the door opening then secure it with the retaining hoop.

Jul 13, 2010 | Frigidaire ATF6000ES Front Load Washer

1 Answer

Replacing door seal front loader bosch


This video will show you how to change a door seal on this bosch

Apr 04, 2010 | Kenmore HE2 Plus Front Load Washer

1 Answer

Frigidaire frontend washer LTF2140ES3 will drain not spin


There is an auxiliary switch in the door lock and switch assembly that is activated at the end of the wash cycle to advance to the spin cycle. When the machine works except advancing to the spin cycle, it signifies that this auxiliary switch cannot be activated and the door lock and switch assembly is faulty. Replaced the door lock and switch assembly (part #131763202) to fix the washer.

Disconnect power to the machine. Open the washer door then look for the retaining hoop securing the door seal around the lip of the door opening. Stretch the retainer spring of the door seal retaining hoop then remove it.

Carefully peel off part of the door seal from the lip of the door opening near the door lock and switch assembly. Remove enough of the door seal to gain access to the door lock and switch assembly.

Remove the screws securing the door lock and switch assembly to the front panel. Once the screws are removed, lift the door lock and switch assembly then pull it away from the front panel.

Take the door lock and switch assembly out of the machine. Disconnect the wires from its terminals then connect it to the new door lock and switch assembly.

Put the new door lock and switch assembly back into position in the front panel and secure it with the securing screws.

Properly put the eased part of the door seal back over the lip of the door opening then secure it with the retaining hoop.

Mar 10, 2010 | Washing Machines

2 Answers

Front dor seal has a tear in at at the bottom. It leaks as soon a


you will need to remove front panel 2 screws at bottom behind kickpanel removed with one screw next to filter cap one more screw behind soap draw ,then remove steel spring clamp holding door seal to outer cover push seal into drum so as not in your way pull down front panel it will then come towards you remove door lock connection and lift away fromt panel this will expose drum front there is another spring clamp on back edge of seal remove this and pull away seal reverse procedure to refit new one may need some detergent on back of seal to make refitting easier.

Feb 04, 2010 | Bosch Axxis WFL 2060 Front Load Washer

1 Answer

How do you get to door switch


front loaders- remove door seal clamp band outer and peel off door seal from front of case with power off the door switch/interlock should the be accessible to the side and by removing front two screws at the lock opening. replacement is reverse.

Mar 13, 2009 | Washing Machines

1 Answer

How to change the door lock unit on a front end loader fridgedair


disconnect power cord open door remove spring from door seal and peel seal away from panel remove the two screws that hold the door lock inplace reach inside move the switch so you can access the 3 electrical connecters from the switch and reverse the process also check the door strike on the door and keep in mind if the pump is restricted it can't drain the water and it won't spin hope this helps out

Dec 21, 2008 | Frigidaire ATF6000ES Front Load Washer

1 Answer

GE Front Loader rubber boot completely out of shape


You can replace the rubber door seal yourself if you are logically minded and are handy with tools. Isolate the washer from the mains supply. Remove the top fixing screws at the back of the washer. Slide the top of the washer to the rear of the washer and remove. Now you will be able to see the outer drum and the securing band to the drum. This needs loosening and moving clear of the outer drum so you can disconnect the seal from the drum. When you open the door, you will find see that the door seal connects to the washer outer body. You should see a holding catch probably made of plastic. This has to be removed and take care not to break anything. When re fitting the seal,you will find on the front inner edge a small hole, this must be in the 6 o'clock position. Working from the door access, feed the new seal on the outer drum and secure it with the retaining band that you removed earlier, at this stage do not fully tighten as you may need to readjust the seal later on. Now working at the door, feed on the door seal and position the small hole at 6 o'clock. If you find that the seal is twisting, then you will have to readjust the the seal on the inner outer drum. When everything is lined up, tighten the inner securing band then the outer retaining band by the door. Recheck that the small hole on the door inner lip is at 6 o'clock and both the door an outer drum securing bands are tight. This done, check for leaks by part filling the washer and then putting the washer on an emptying cycle. If all is well, then isolate the power to the washer and refit the the top of the washer and secure with the screws you removed earlier. On no account put your hands or tools inside the washer when it is on and connected to the power supply.

I have not yet replaced a door seal on your model of washer, but I have done quite a few and the process is the same. I hope you can follow these instructions and if you come across a snag, think about it and i am sure you will find the solution. You can always get to me at FixYa.

Oct 27, 2008 | GE Energy Star WCVH6260F Front Load Washer

1 Answer

HELP!! Leaks!! Leaks!!!


the inner tub and outer tub has a seal under the agitator. this must be replaced. use a spanner or a large channel lock plier to remove the nut. seal is underneath it.

Sep 04, 2007 | Frigidaire GLWS1233A Top Load Washer

Not finding what you are looking for?
Frigidaire ATF6000ES Front Load Washer Logo

Related Topics:

121 people viewed this question

Ask a Question

Usually answered in minutes!

Top Frigidaire Washing Machines Experts

Gerry Harvey
Gerry Harvey

Level 3 Expert

1479 Answers

J. Bradshaw

Level 2 Expert

121 Answers

Archie Ferrarini
Archie Ferrarini

Level 3 Expert

869 Answers

Are you a Frigidaire Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...