Question about Poulan Pro Pp125 25cc Gas Straight Shaft Attachment Capable String Trimmer

2 Answers

How do you wind replacement line to the Poulan Pro String Trimmer?

Posted by on

  • Mark Waldee
    Mark Waldee Jun 15, 2012

    My PP125 the string rolled back up inside the first time I used it and it was a solid piece of string. called Poulan they were no help and neither was Wally World. Any suggestions?

×

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 1,040 Answers

If it is a duel line trimmer then:

Cut two separate pieces of string, about 7 ft. each.

Stick the end of the line in the hole on the inside of spool.

Wind clockwise onto spool, putting the line that is closest to the ground on first.

Once you have winded this piece on, lock the last 4 inches of line through the slits on spool.

Repeat process for second piece of line, locking the last 4 inches in slot opposite the other locked in piece.

Put the spool on the trimmer, feeding the end of lines through either hole on trimmer.

Before you push the spool all the way on, pull the strings out of the locked position.

If it is a single line trimmer, just wind a single piece of string clockwise onto spool.

Jim

Posted on Jul 03, 2009

  • Jim Parker
    Jim Parker Jul 06, 2009

    Did this solution solve the problem?



    Jim

  • Jim Parker
    Jim Parker Nov 26, 2009

    Thanks for the rating.

    If you should have any questions about
    "Drywall Finishing/Patching", or know someone who does, put your
    questions to Category:"Tools- Building & Power- HAND TOOLS" at
    FixYa.com

    Thanks Again,

    Jim



















×

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

String is wound clockwise when looking from the top down.

Posted on Aug 15, 2010

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 76 Answers

SOURCE: replace string on trimmer

Hi
check in you tube .
The video is talking about trimmer strings in general , but my experience is that all trimmers are more or less the same.
hope it helps

http://www.youtube.com/watch?v=WFu66Q6J62Q

Posted on Jul 16, 2009

rycgl
  • 1545 Answers

SOURCE: trying to replace the fuel line and the primer

The smaller line is connected to the fuel filter in the tank and goes on the carb body opposite the end with the hole in the cover. A larger diameter line coming out of the tank is the fuel return line and has the little connector on it just inside the tank to hold it in place there
It goes on the carb body (if primer is on carb) by the bulb.
If there is an external bulb...the small line is the same...there would be a larger line going from the carb body (nearest the end with a hole in the cover) to the smaller nipple on the primer bulb. A third larger diameter line would be connected to the larger nipple on the primer bulb and running to the little nylon connector inside the tank. This is the fuel return line and the smaller diameter line is of course the fuel supply line.

Posted on Aug 07, 2010

  • 1 Answer

SOURCE: how do you change a head on a poulan pro trimmer

Just below the gearbox there is a slot and when you turn the shaft there is a slot on the shaft that lines up with that one. Stick a screwdriver in the slot when they are lined up and then grab the head and turn it clockwise. (the threads are reversed)
3_10_2012_9_49_47_pm.jpg

Posted on Mar 10, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I remove the shaft from my trimmer


String Trimmer Drive Shaft Replacement - Poulan Pro ...

? 2:18
www.youtube.com/watch?v=A_Sv1S7r_-o
Mar 4, 2013 - Uploaded by RepairClinic.com
This video provides step-by-step instructions for replacing the lower drive shaft on Poulan string trimmers. The .

Jul 28, 2015 | Garden

1 Answer

Poulan25cc 16 inch how do i rewind trimmer line on my poulan 1500 gas trimmer


You should wind it on the spool the opposite direction that it spins while operating it. If you wind it in the same direction as the spin, the line will come off the spool when in operation.

Jim

Jul 29, 2011 | Poulan 25cc 2-Cycle Gas Powered String...

1 Answer

HOW DO I INSTALL A NEW STRING IN A PRO CUT 11 for Ryobi RLT30CD trimmer


LINE REPLACEMENT (Fig. 8) (For Reel EasyTM Head) Use 2.4mm monofilament string. Use original manufacturer's replacement string for best performance. n Stop the engine and disconnect the spark plug wire. n Cut one piece of string approximately 7.6m in length. n Rotate knob on string head until line on knob aligns with arrows on top of string head. n Insert one end of string into eyelet located on the side of the string head and push until string comes out through eyelet on the other side. Continue to push string through the string head until the middle section of the string is inside the string head and string outside the string head is evenly divided on each side. n Rotate the knob counterclockwise on the string head to wind the string. Wind the string until approximately 20cm remains protruding from the string head. INSTALLING STRING IN PRO CUT II STRING HEAD Use monofilament string between 2.4 mm and 2.7 mm diameter. Use original manufacturer's replacement string for best performance. n Stop the engine and disconnect the spark plug wire. n Gather two of the pre-cut lengths of trimmer line provided or cut two pieces of trimmer line, in 28 cm lengths. n Insert the strings into the slots located on the sides of the string head. String should be pushed in until approximately 2 cm protrudes from the holes on the top of the string head. n Remove old string by pulling it from the holes located on the top of the string head. http://www.screwfix.com/sfd/i/cat/pdfs/89/p4763889.pdf

Oct 29, 2010 | Ryobi 30 Cubic Centimeter Curved Shaft Gas...

1 Answer

Replace pull string (how to put string on after taking cover off)


Basically, pull the string through the winding hole and knot it off insuring no more than .25" tail on the knot and pull tight. :)

Jul 22, 2010 | Poulan/Weed Eater No. Te475 952711797 17"...

1 Answer

Out of trimmer line


You should be able to just pull the spool off the end. Try. Once you have it off, look closely at the spool. You will find the starting hole/s and the direction to wind the string. Good luck...Lee

Jun 10, 2010 | Poulan/Weed Eater No. Te475 952711797 17"...

1 Answer

How do I load string in a P2500 string trimmer??


Remove spool by firmly pulling on tap button. Cut two pieces of line (0.080) about 12 feet. Insert the two ends of the line into the small holes inside the spool. Wind the lines evenly and tightly on the spool. Wind the string in the direction of the arrows on the spool. Push the lines into the notches on the spool leaving three or five inches hanging there. Insert the two ends in the two holes in the hub. Align the notches on the spool with the holes in the hub and push it in until it snaps into place. Pull on the lines to release them from the notches.

May 03, 2010 | Poulan 25cc 2-Cycle Gas Powered String...

1 Answer

How do you put string in


turn trimmer upside down grab the spool head firmly and pull out replace string but wind in the way arrow shows you and replace fishing the loose end back through the hole on the side as you slip back together ,once together grab string and pull to remove any slack and away you go

Aug 22, 2009 | Poulan/Weed Eater No. Te475 952711797 17"...

1 Answer

String for a Poulan Pro PPB330


Hello,

Pull your spool off, and look next to the notches on the bottom of the spool. The decimal number is the size of line that you can use. Some spools will have more than one size listed; they can use either size.

Best regards, --W/D--

Aug 21, 2009 | Poulan 25cc 2-Cycle Gas Powered String...

3 Answers

Renewing the cutting line


This product is driving me nuts - if someone can't help then its going into the bin

Aug 28, 2008 | Poulan 25cc 2-Cycle Gas Powered String...

Not finding what you are looking for?
Poulan Pro Pp125 25cc Gas Straight Shaft Attachment Capable String Trimmer Logo

Related Topics:

1,038 people viewed this question

Ask a Question

Usually answered in minutes!

Top Poulan Garden Experts

Doctor PC
Doctor PC

Level 3 Expert

7733 Answers

Roland W VanLue
Roland W VanLue

Level 3 Expert

486 Answers

Phil Walker
Phil Walker

Level 3 Expert

605 Answers

Are you a Poulan Garden Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...