Question about Microsoft Windows Vista Ultimate Edition

1 Answer

Can't start automaticlly call for service

Tries to start says wait while computer tries to start will take few minutes

Posted by on

  • ultimitloozr May 11, 2010

    Tries to start? Did you just perform an upgrade to Vista?

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Mentor:

    An expert who has written 3 tips or uploaded 2 video tips.

  • Contributor
  • 169 Answers

Hi

please try to folow these steps .

try to boot the computer from cd.
you needto change the boot oder from hardisk to cd rom

once the computer start booting from cd then try to click on to the option that says repair the operating system .once the os gets repaired your system would run fine

if you once again face a same problem i would suggest to go to http://techbuddies.org and from their you can download the manual guide of OS repair .if you face a problem chat with techbuddies and they will help you on same

Posted on Jul 08, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I need to bypass the password when i start my dell inspiron 910 mini n series. when password is entered wrong three times i get message with System disabled [13667] Service tag [21LTWF1].Please help


Disconnect the cmos battery and any power supply connected to unit - wait a few minutes and also push and hold the on button. Then after a few more, put back the battery and the cleared cmos should allow you in without a password.

Jul 24, 2017 | Dell Computers & Internet

1 Answer

Toyota 4runner problems


check for an over heating situation with the motor as what you say indicates engine over heating.

Jan 23, 2014 | Cars & Trucks

1 Answer

2003 Saturn Ion won't start in the cold weather


First of all your service light came on so give it a service then have the service light reset then check the thermastac, water levels and the choke is working properly and all the elecric working parts are good

Jul 05, 2017 | 2003 Saturn ION

1 Answer

Car starts ok when cold but acts like it is flooded when warm


Is the check engine light on while you're cranking the engine?

Jul 27, 2017 | 1998 Ford Taurus

1 Answer

How do i reset the service light for the BMW 320i 2006 model. The key is a slot in type. To start, there is a start and stop button.


If you had work done on the car, they should have disconnected the battery. This "re-sets" the on-board computer to adjust to the new changes.

If you are referring to the "check engine" light as the "service light", here's what you can try:
disconnect the negative battery cable. Wait for 15 minutes, then re-connect. Hopefully that re-sets your on-board computer.

Some cars require a few more starts before the computer resets, so maybe you just haven't started it enough times since it was serviced.

Otherwise, I don't have enough info for a complete answer.

Feb 17, 2011 | 2008 BMW 3 Series

1 Answer

In few minutes after turn on the projector (Eiki Lc-xnb4m) , it shut off automaticlly. and i connect notebook with the projector ,no any reaction. i don't know how to operate it?


are any of the leds flashing? could be overheating. blow out the dust with canned air. if the lamp is old, it could be that it needs to be replaced. if the fans go out immediately as well, it could be the power supply.

Aug 22, 2009 | Eiki LC-XE10 Projector Multimedia...

1 Answer

Code F 40


Hello homefolks
Welcome to fixya.
I'm Huuum and happy to assist you,



You said, Your washer starts to wash and code come up it stop then starts runs for a
few minutes then code comes up again and does this over and over
can't finish a load. Model # 2709

Sounds like we need to try to reset the system!

Huuum At your service!
Lets try this,
Like with an error code.
This can reset the system if it is electronic!
Unplug the washer and wait a 5 minutes then restart it.
If you can't reach the plug, use the breaker to cut the power for 5 minutes.

It's like rebooting your computer when its acting strange!
Usually it corrects some error problems if they are not serious.
Or they are sometimes just a glitch.

Let me know how it works! Waiting for your reply!
Please remember to leave a rating when you are done!
thank You huuum




Sep 25, 2008 | Kenmore Oasis HE 27082 Top Load Washer

Not finding what you are looking for?
Microsoft Windows Vista Ultimate Edition Logo

Related Topics:

58 people viewed this question

Ask a Question

Usually answered in minutes!

Top Microsoft Computers & Internet Experts

micky dee

Level 3 Expert

2727 Answers

Piyal Perera
Piyal Perera

Level 3 Expert

528 Answers

Les Dickinson
Les Dickinson

Level 3 Expert

18392 Answers

Are you a Microsoft Computer and Internet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...