Support prosesser i have Aopen MX46L mother board with 1.70 Ghz processer . now i want upgrade processer tell me how much support processer this board Aopen MX46L . thanks

Hello the drivers can be downloaded here:


http://global.aopen.com/products_download.aspx?auno=179


Good luck

I don't think 96MB is correct. Right click My Computer > Properties will tell you how much RAM you have.

Unless you have a 64bit system, the max is usually 4GB.

This motherboard has two 184-pin DIMM sockets that allow you to install DDR 266 memory up to 2 GB.

here is a list of processors supported on that machine

Intel Pentium M 745 (1.8-GHz) with 400-MHz front
side bus (FSB)

Intel Pentium M 735 (1.7-GHz) with 400-MHz FSB

Intel Pentium M 725 (1.6-GHz) with 400-MHz FSB

Intel Pentium M 710 TJ85 (1.4-GHz) with 400-MHz FSB;
operates at a lower temperature than other processors

Intel Celeron M 340 (1.5-GHz) with 400-MHz FSB

Intel Celeron M 330 (1.4-GHz) with 400-MHz FSB

Is the graphics supported on the motherboard or is there an expansion slot card for video graphics?

If you mean that your processor pins does not fit in your motherboard, then they are not compatible. The processor pins must be exactly fit the motherboard.
Besides, the processor type must be supported by the motherboard (If the motherboard is supporting P4, Core Dou, Quad, Celeron, Athlon, etc). You have to install the right processor for a particular motherboard. You have to know what particular
processor is supported by your motherboard.. In your
case, I believe it supports Pentium 4, but I cannot
give you the exact speed in Ghz, as well as the clock speed. You can ask the dealer about it.

Here is the download site for Aopen motherboard. Download a manual and i am sure that the locations that you are looking for wil bbe illistrated. If not their are also 4 more pages of downloads for that MB.

http://download.aopen.com.tw/Default.aspx

Do not know much about mac but can you change settings on M/board by using jumpers to upgrade bus speed etc or in BIOS

To enter setup (Refering to the bios/cmos), press the Delete key very two seconds untill the bios main menu loads. You need to go to the menu heading - Boot.
If you added another hard drive to you're system the IDE (hard drive) it's jumper settings may not be correctly set. If there are now two IDE drives both the primary master & secondary drive's jumpers must be set correctly. You will ned to look at the white sticker on the drive for the correct jumper settings. Many primary IDE drives pin jumper is set as a single master drive with out a secondayr drive attached in the system. When you add a second drive the pin jumper one the master drive will most likely need to be changed to master with a slave. The second drive will also need it's jumper set as a slave drive. Once this has been adjusted you need to enter the bios & make sure you're primary master drive is set in the boot order. Most PC's boot order is as follows.
1st Boot device, floppy drive. (If one is connected to the system).
2nd boot device, CD-ROM drive.
3rd boot device, master IDE drive.
Please use the help of you're manual to guide you for these settings.
AOpen MX46L web site. http://download.aopen.com.tw/Default.aspx
You must set the three drop down menu's to get you're board's drivers & manual. In the first menu choose motherboard, in the second menu choose MX46L & in the last menu choose manual. For drivers, the third menu choose drivers.

Still heave more questions? Just ask.
Mike

first, ensure that only one master hard drive is connected (also disconnect cdrom(s). Next, at startup press the key (DEL or F2) to BIOS screen. then make sure that only the master hard drive in position 1 is listed or choose AUTO detect. now reboot and report if any progress. If no further progress, then master hard drive has failed somehow, but to be certain, try that drive on another pc as a slave just to test spin-up.