Question about Fuji Pictrography 3500 Printer

4 Answers

Fuji Pictrography 3500 Service code H29?

Hello, I was just wondering what code Service H29 is for . It is not in the manual.

Posted by on

  • 1 more comment 
  • Previz Nov 27, 2007

    I am getting the exact same error, and cannot find the solution anywhere. Any help would be appreciated!

  • fujiman Dec 15, 2007

    Hello, I finally found what the error code is. The sensor in the refuse arms. I hold my refuse arms up and start the machine, it starts and says refuse full, soon as I release these back down, the error starts up. I think that the arms got bent a little when I had a big jam. I am looking on Ebay for a used printer it looks as though a 3000 and 3500 both have the exact same arms and sensors. I could only imagine what a sensor would cost to replace from Fuji.

  • Anonymous Nov 05, 2008

    Is there any independent service place for Fuji Pictrography in NYC arae?



4 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Refuse light and alarm stay on inspite of the fact the tray is empty. Sensor switch is clean with no obstruction. Printer has been restarted with no solution. Any ideas? Thanks

Posted on Sep 02, 2009

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

I got this error message as well. After much hassle with the technical support channels, turned out to be as simple as emptying the donor refuse. H-29 is apparently the error code for the Refuse Donor Full sensor. Don't know why the Refuse Full light did not just come on, I imagine the sheets were jammed in the refuse collection tray. If emptying the tray does not clear the code, other suggestions are that the arms on the tray are bent or damaged or that there is dirt on the black U-shaped sensor in the tray.

Posted on Dec 09, 2008


I have a Fuji 3000 and a 3500 both in good working order with very low use and am lookig for anyone who may be intereted in buying them

Posted on Jul 24, 2008

I have the Pictogrphy 3500 service manual, however I also can not find error code H29.

I need to refresh myself with the printer operation and need to fix it myself.

Need more info drop me a line santilaat methownetcom

Posted on Dec 15, 2007

1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

كم سعرها

Can you please explain me your problem in details.

Jan 17, 2011 | Fuji Pictrography 3500 Printer

1 Answer

I have a PG 4000 and in need of the the drivers for windows xp

typing your product name and model number in google or your product's website followed by download

Sep 26, 2010 | Fuji Pictrography 3500 Printer

1 Answer

Pictro 3500 does not separate donor & receiver. Reports jams at 5. I have cleared it repeatedly. Never any damaged paper or donor sticking in the process but the cycle never gets completed.

The drum wait position or mating timing parameters need to be adjusted, See page 2.4.5 in service manual. Its a easy fix. Also dont screw the water filter on to tight or it will **** air and limit water in water tray.

Dec 07, 2009 | Fuji Pictrography 3500 Printer

1 Answer

Does the Fugi Pictrography 4500 wont print

Buy distilled water from the grocery store for $1.00 and then clean out the water tank and refill to the fill line. Change the water filter every 6 months (according to the manual). Clean out the water hoses by ramming soapy chopsticks through them and then forcing some water through them.

Mar 06, 2009 | Fuji Pictrography 4500 Thermal Printer

1 Answer

Fuji Pictrography 3500 printer paper jam at 5

start printer up wait 5 minutes then open the mai door get a cup and put it under the return drain valve for the water were it returns back to the water bottle [do not turn the printer off] push a pen into the center of the drain valve which will empty the water tray you should have about 120ml if not the prints are sticking together because of the lack of water.this valve could be leaking or the water pump is naff

Dec 23, 2008 | Fuji Pictrography 3500 Printer

1 Answer

"Specified media does not match media in printer"

you have to specify that you want the job print on glossy paper in order to get rid of this message. You may have to resend the job.

Nov 25, 2008 | Fuji Pictrography 3500 Printer

1 Answer

Fujifilm ask-4000

I have the driver disk if you need it.

Oct 03, 2008 | Fuji Pictrography 3500 Printer

1 Answer

Fuji Pictro Proof e252

E 252 doesn't seem to be listed in the troubleshooting guide. Are you sure of the number?

May 21, 2008 | Fuji Pictrography 4500 Thermal Printer

2 Answers

Do you have a service manual for the 4500N, I need one

Hello, try this: pull and open the refuse compartiment and look in the empty space. you will see the J9 trap. open it and look for any paper jam.

May 15, 2008 | Fuji Pictrography 4500 Thermal Printer

Not finding what you are looking for?
Fuji Pictrography 3500 Printer Logo

Related Topics:

367 people viewed this question

Ask a Question

Usually answered in minutes!

Top Fuji Office Equipment & Supplies Experts


Level 2 Expert

211 Answers

mukhtar21 shaikh
mukhtar21 shaikh

Level 3 Expert

2022 Answers

Dave Busselle

Level 1 Expert

54 Answers

Are you a Fuji Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides