Question about Canon Office Equipment & Supplies

1 Answer

When power turned on copier comes on then turns--canon 6012F

When power turned on copier comes on then turns off--whats the problem with my canon 6012F?

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Vice President:

    An expert whose answer gotĀ voted for 100 times.

    Sniper:

    An expert who has posted more than 50 answers, of which 90% or more were rated as helpful.

  • Expert
  • 118 Answers

Check your fixing heater lamp or thermal fuse maybe open or the exposure lamp is defective ,check also for open thermal fuse in series with exposure lamp this a canon generic error if one of the lamps is busted or the AC supply going to the lamps was not detected during power on if the machine detect this situation it will switch off automatically.hope this will help

Posted on Jun 28, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

No power to my canon ip 2770 even turn on It is left on after printing 1 page docs. but later on noticed theres no longer power and wont turn on at all.what is the possible problem?


First of all, is there a green power light on the control panel, if not check that the main power switch is on, located at the right side lower right. Check that the main circuit breaker hasn't been blown on the copier. If these are good, turn off the main power switch and back on again. Look on the display to see if there is a progress bar on it. This is booting up the copier and if all goes well it will come to ready. If not it will give you an error message and then I will have to know what that is help any more.

May 08, 2017 | Canon Office Equipment & Supplies

Tip

ERROR codes Canon 6012F


Canon 6012F C No problem. Means that the machine is correcting the fuser film tracking. CC Drum must be changed. Could be the drum serial number is identified by the logic as being non-compatible to that particular copier. E000 Low fuser temperature E001 High fuser temperature E002 High fuser temperature E003 Erratic fuser temperature E007 Fuser film off track and will not repair itself E010 Main drive problem E030 Counter problem E064 Scan problem, or power supply E202 Scan problem E210 Lens drive problem or lens sensor E220 Exposure lamp stays on or off E240 DC controller (main board) or composite power supply E261 Zero cross problem. Power frequency or composite power supply E400 Communication problem between boards E803 24 volt problem EO Fuser problem H Fuser overheat

on Jan 19, 2010 | Office Equipment & Supplies

2 Answers

Canon ir600 error code E220


sira canon 600 mechan E220 has cmming turn of the power has coming solve the problam how to slove the problam slove it

Jul 17, 2012 | Canon ImageRunner IR600 Copier

3 Answers

My canon MF4412 is power on but display is coming turn the main power on E202-0002


my mf4412 printer displaying a problem e202-0002 and red button continue burning

Jun 24, 2012 | Canon Office Equipment & Supplies

1 Answer

Message d'error ir 2200


Hard drive is dead or dying. Will need to get tech to come out, replace hdd, format and load firmware using SST.

Here's something you can try to possibly keep the copier going till a technician can come. Turn copier off using main power switch (on right hand side of copier). Press 1 and 9 while turning it back on. Hopefully you see rectangles dropping on the screen. When this is finished should see download on the screen. Turn copier off then on again. If copier comes up with normal screen should work a little longer, but hard drive will die.

Jul 01, 2009 | Canon (6981A002AA) for imagerunner 2200,...

Not finding what you are looking for?
Office Equipment & Supplies Logo

Related Topics:

68 people viewed this question

Ask a Question

Usually answered in minutes!

Top Canon Office Equipment & Supplies Experts

kakima

Level 3 Expert

102366 Answers

old marine
old marine

Level 3 Expert

1979 Answers

Doctor PC
Doctor PC

Level 3 Expert

7733 Answers

Are you a Canon Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...