Question about Sharp Aquos LC-46D62U 46 in. LCD HDTV

Open Question

Power and opc lights flashing - Sharp Aquos LC-46D62U 46 in. LCD HDTV

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
  • 9 Answers

SOURCE: power light flashes twice,then opc flashes once then power again

In all the time that you have had the tv have you applied 2 firmware updates that some of the tv's need to avoid other known issues with the lcd in the future. These firmware updates are for the main cpu PH1UU112 and the monitor MD1UA104. I don't know if this is the case for you but it worked for me. Call Sharp at 1-800-237-4277.

Posted on Oct 07, 2009

Ad
  • 8457 Answers

SOURCE: no picture no sound opc light and power light

This is very common in sharp tvs.U turn it on.U get power on light stable right?U hear a click,one or twice,sometime tv is good right?Sometime POWER light and OPC light flashes?Push the power button on/off couples times will work, picture will come on.If keep trying off/on couples time after POWER and OPC flashes,don't ever stop and never get backlight and picture.Ur Video backlight board is dead must replaced.

Posted on Dec 28, 2009

  • 63 Answers

SOURCE: power light and OPC light flash once then the

Fault protection mode.... More than likely you have blown Uf Caps on the PSB-Power supply board. Recap with new Uf caps. A few bucks, solder and a soldering iron.

Posted on Jun 30, 2010

budmrtn
  • 11361 Answers

SOURCE: will not power on, like others have had issues

Flashing power and OPC (OPC is for automatic brightness control that adjust the brightness according to room light) flashing means you have either thw power supply module or the backlight inverter module problem.
If you are going to DIY and have proper tools, electronics knowledge, and know safety precaution then please read on:

Please see my basic troubleshooting guide here:
http://www.fixya.com/support/r5093881-lcd_flat_panel_tv_troubleshooting_guide

http://s807.photobucket.com/home/budm/allalbums

http://en.wikipedia.org/wiki/Capacitor_plague

Parts: www.shopjimmy.com

Posted on Jul 14, 2010

bshldn
  • 736 Answers

SOURCE: TV will not turn on. There are two lights in front

Sounds like your screen is broken or has been impacted. Force the television on by doing this: Unplug it and on the side of the television where the panel buttons are hold down the ch- and vol+ buttons. Then plug in the television while still holding them down. The television should come on and you see the cracks. Unfortunately it can't be repaired.

If it isn't ch- and vol + then try ch + and vol -.

Posted on Feb 05, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Model LC-465B57U flashing power light and opc light


Hi Tracy,
It appears your TV is not sequencing properly. By the order given in your instructions with the controller you are tuning, continue with a code until it satisfies .


Press setup- blinks twice. Enter TV manufacturer code- press enter. Light should flash once. Press on . After it works . Go through all the functions. Up- Down, loudness, channels,& on -off .


Fare .Well.

Dec 12, 2014 | Sharp Televison & Video

1 Answer

How can I get the TV screen to come on when only the power and OPC lights flash?


Even when the TV is off, some electronic components in your TV consumes power 24 hours a day. Maybe a power surge damaged your TV when the power came back on.

Aug 02, 2014 | Sharp LC-32SB24U 32 in. LCD TV

2 Answers

I have an aquios LC-42D64U which suddenly has the following two lights blinking power & OPC. They both blink, once together, the second blink is only the power, and repeating the sequence. I've...


Sharp LED/LCD EEP cleared Step 1 Remove Mains Plug 2 Press On/Off Switch from LED/LCD Panel 3 Press Ch Down & Input Switch together and plug in mains cord 4 LED/LCD will start 5 "K" will appier on Screen 6 Press Ch Down & Vol Down from LED/LED Panel 7 1/9 Page will appier on Screen 8 Go to 9/10 page by pressing Up & Down arrow of remote 9 Select EEP Cleared 10 Press ok button from remote 11 On Screen dispay EEP running 12 Remove Mains Plug after complete EEP Run 13 Restart LED/LCD

Feb 05, 2011 | Sharp Aquos LC-46D62U 46 in. LCD HDTV

1 Answer

MY Sharp LC46D62U wont turn on


Power and OPC LED lights flashes?Common on Sharp LCD tv.Tv is still useable.Tv have Tuner signal board problems.Every times Power and OPC LED lights flashes.Just push the remote power button again and wait.Sometimes Power and OPC LED light will flashes require push power again wait again Power and OPC will flashes two or three time push power button and wait.Must do this two or three time before the backlight will light up and tv work.

Jan 07, 2011 | Sharp Aquos LC-46D62U 46 in. LCD HDTV

1 Answer

Tv wont turn on used it for two months and one day it turns on then the power led light flashes and the opc led light ...


This tv still under warrenty?Yes take ur warrenty repair.This problems very common on Sharp LCD tvs.I have one too.This tv have a Tuner signal board problems.But this tv still use able.Just push power button again after the POWER and OPC flashes.POWER and OPC some will flashes again and wait just push the power button again and wait.Sometimes have to push power buttons and wait power button push out of three or four times power button push POWER and OPC flashes.Than tv will work again.

Jan 06, 2011 | Sharp LC-52D64U 52 in. LCD HDTV

1 Answer

THE TV IS CUTTING OFF BY ITSELF AND THE OPC LIGHT IS BLINKING


This problems very common on Sharp Tv.Do ur tv LED power light turn on solid first.Few mins,than LED,OPC flahes.Power LED,OPC flashes,push power button again,do this at leat 5 or 6 times somtimes the backlight will come back on and work.The power LED,OPC light flashes,turn off/on more than 5 or 6 times don't work.Ur Tuner signal board is dead,must replaced.

Mar 30, 2010 | Sharp Aquos LC-42D62U 42 in. LCD HDTV

1 Answer

Aquos has the power light and OPC light flasing but nothing works


First turn on power light stable at all?Power and OPC lights well flash,but push on/off power button do this couple times after the Power and OPC flashes well backlight come back on well work.This problem very common is Sharp tv.

Jan 17, 2010 | Sharp Aquos LC-46D62U 46 in. LCD HDTV

2 Answers

No picture no sound opc light and power light


This is very common in sharp tvs.U turn it on.U get power on light stable right?U hear a click,one or twice,sometime tv is good right?Sometime POWER light and OPC light flashes?Push the power button on/off couples times will work, picture will come on.If keep trying off/on couples time after POWER and OPC flashes,don't ever stop and never get backlight and picture.Ur Video backlight board is dead must replaced.

Dec 28, 2009 | Sharp Aquos LC-46D62U 46 in. LCD HDTV

3 Answers

OPC/DL light flashing Same problem of black screen and green lights flashing at power and OPC Help....


WHEN FLAT SCREEN SHARP LCD IS ON .. BLIKNING ON BOTTOM OF SCREEN SAYS OPC

Dec 08, 2008 | Televison & Video

Not finding what you are looking for?
Sharp Aquos LC-46D62U 46 in. LCD HDTV Logo

Related Topics:

116 people viewed this question

Ask a Question

Usually answered in minutes!

Top Sharp Televison & Video Experts

The Knight
The Knight

Level 3 Expert

76060 Answers

Jaime Hernandez

Level 3 Expert

2337 Answers

Cindy Wells

Level 3 Expert

5913 Answers

Are you a Sharp Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...