Question about KitchenAid KSM90 Ultra Power Series Stand Mixer
Posted by Anonymous on
Visit lanas-kenwood-spares.co.uk where you can purchase what you require to fix the problem and get replies to your questions
Posted on May 15, 2015
Solution for these KitchenAid Stand Mixer Models
Posted on Jun 21, 2014
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
Here's a link to this great service
Posted on Jan 02, 2017
SOURCE: kitchenaid mixer k45ss slow gear
If you look into the brush holder you will see a stopper at the botom ,(this is so when brushes are wore the spring is not driven into armature) .. the brushes have to be inserted so the groove is lined up , try that
Posted on Apr 07, 2008
Hi Gail. Kitchenaid no longer has a Parts List for your model. This means that they consider it obsolete. Do an Internet search for parts. You may get lucky. Good luck!
If this solution has assisted you, please rate it. ricardok45
Posted on Apr 04, 2009
jrichards - I hate it when that happens! It seems that power is not getting to the armature from the brushes so I would suspect that one or both of the brushes is (are) not seated properly. Did you remove the brushes to replace them or were you just inspecting them? I'd suggest removing them again and making sure the contacts are facing in the right direction to contact the armature. The concave contact face should be resting completely on the armature. If you've turned it 90 degrees too much, it wont' seat properly. I hope this helps... Howard, Burke, VA
Posted on Nov 03, 2009
You don't need to seat the brushes. Remove the brush caps and pull the brushes out by their springs, being VERY careful to note the position of them since they only go back in one way. Measure the free length of the spring before pulling it out. It is critical that you write down the length sticking out with very slight pressure on it so that it is seated against the armature when you measure.
Clean the curved surface of the carbon brushes with a sharp knife being careful not to scratch the curved surface. If you have them installed wrong they will not go all the way in and will not contact the armature and it will not run. Measure the length, as done above, of the spring to make sure it is in correctly!! If it is not in correctly the spring will stick out 1/4 inch longer than it should.
Posted on Apr 21, 2010
SOURCE: which direction do I place
In order to place the brushes the proper way you are going to need a flashlight. What you need to do is shine a light up in the brush hole and see where the indention is at the back of the hole and put the tapered edge to that side of the square and then you will have to do the same thing on the other side. I have been working on these for about 10 years and still have to look to make sure they are in the proper direction.
I hope I was able to help and would like to thank you for choosing FIxYa to answer your questions.
Posted on Mar 06, 2011
Tips for a great answer:
Jan 10, 2012 | KitchenAid K5SS Heavy Duty Commercial...
Jul 30, 2011 | KitchenAid K45SS Classic Stand Mixer
Sep 07, 2017 | KitchenAid Food Mixers
Aug 11, 2010 | KitchenAid KSM90 Ultra Power Series Stand...
Apr 16, 2017 | KitchenAid KITCHEN AID 5 Quart Artisan...
Apr 11, 2010 | KitchenAid KP2671 Professional 6 Series...
Apr 18, 2009 | KitchenAid KSM90 Ultra Power Series Stand...
Apr 02, 2009 | KitchenAid KSM5PS Heavy Duty Stand Mixer
Nov 03, 2007 | KitchenAid KSM90 Ultra Power Series Stand...
1,298 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: