Question about Ricoh KR-5 SUPER II 35mm SLR Camera

1 Answer


Posted by on


1 Answer

  • Level 1:

    An expert who has achieved level 1.


    An expert that hasĀ over 10 points.


    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 8 Answers

It is better to send the unit out for repair. it seems that the liquid has go through the terminals.

better not to use the unit to avoid any electrical short circuit to the main board of the camera.

the unit needs to be clean completely and check with some special tools.

hope this initial info helps

Posted on Jun 26, 2009


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

2 Answers

Lite meter don't work I bought it off internet seller said it was in looks that's all

The built-in through-the-lens CdS exposure metering system of your KR-5 SUPER operates on power activated by two 1.5V SR-44 silver oxide batteries, which are supplied together with your camera. Have you changed the battery? Also, many of these older cameras the light meters are not very good. I would suggest getting one of the free smartphone light meter apps.

Oct 08, 2015 | Ricoh KR-5 SUPER II 35mm SLR Camera

1 Answer

Oil pan change on ford 550 6.0 2004

If it is a rust leak the only way to fix with out moveing engine is to drain oil , clean area on pan (brake cleaner works well)with a clean rag. Once clean sand area of leak. JB weld mix both tubes on cardboard use putty knife or bondo scrapers to mix and apply to holes in pan. It will last for years let it set up for a couple hours it will be good as new

Apr 08, 2014 | 2012 Ford F-450 Super Duty

1 Answer

I have a antifreeze leak on a 2003 ford sports trac Hi Donna,here's a link to the water pump diagram,is the mating surface that the gasket goes on clean and not badly scraped up from removing gasket,the pump itself is aluminum and could be warped and not sealing good causing it to leak,maybe you need a new water pump,hose on that side isn't leaking?

Oct 12, 2012 | Ford Vehicle Parts & Accessories

1 Answer

Water from ac leaking inside on floor, drain tube open

Pull the fan and blower out of the enclosure and make sure the drain is really open, i will bet it isn't and has leaves blocking it on the inside.

Sep 07, 2012 | Dodge Cars & Trucks

1 Answer

The liquids start leaking as soon as I put them in the pan

If the leak isn't too bad in a pinch you can put all the dry ingredients except for the yeast and push start then start gently pouring in your liquid so that it is slowly absorbed once all the liquid is in add the yeast last. As long as your liquid doesn't puddle up that should work otherwise you'll need to get a new pan or a new machine. If you decide on a replacement machine let me know I have several for sale that are super nice. One is unused! thanks,

Aug 24, 2011 | Black & Decker Kitchen Appliances - Others

1 Answer

I have a Hayward super pump. I just changed the housing gasket, but it is still leaking from somewhere at the bottom. I can't see where it is exactly leaking because there is no clearance between the pump...

You forgot to replace the most important part...The" shaft seal".It is behind the impeller. Be sure to remove all the pieces of the old seal off the impeller ,(they always come off in pieces) and put silicone on the rubber part that sets in the pump housing. Make sure you keep the white porcelain surface perfectly clean, and you will also need to replace the ribbon gasket again.

Sep 30, 2010 | Hayward 1 12 Hp Super Swimming Pool Pump...

1 Answer

Can the 35mm SLR Ricoh Kr-5 Super II camera still work with the batteries dead?

Straightforward answer: no. Everything needs power to work except for the self timer, but even that won't fire the shutter without battery power.

Sep 12, 2010 | Ricoh KR-5 SUPER II 35mm SLR Camera

2 Answers

Ricoh KR-5 light meter needle won't move, new batteries

About the only thing you can do is clean the batt. cover and contacts in batt holder. Make sure batts are good. No parts are avail. for this model. However this is a rugged camera and you can buy a hand held light meter inexpensive.

Oct 29, 2008 | Ricoh KR-5 SUPER II 35mm SLR Camera

1 Answer

Ricoh kr5 super light meter does not work

About the only thing you can do is clean the batt. cover and contacts in batt. holder,use a pencil eraser, be careful with the contacts in holder. There are no parts avail. for this model. However this is a rugged camera and you could buy a hand held light meter.

Oct 18, 2008 | Ricoh KR-5 SUPER II 35mm SLR Camera

1 Answer

Sears ks super camera.

You'll have to remove the bottom cover. Either the mirror box or the shutter are stuck. re-cocking it is possible by moving the wind stop clear of the bottom portion of the film advance shaft.

Aug 20, 2008 | Ricoh KR-5 SUPER II 35mm SLR Camera

Not finding what you are looking for?
Ricoh KR-5 SUPER II 35mm SLR Camera Logo

Related Topics:

208 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ricoh Photography Experts

Lyle Siemens
Lyle Siemens

Level 2 Expert

328 Answers


Level 3 Expert

80637 Answers


Level 2 Expert

120 Answers

Are you a Ricoh Photography Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides