Question about LG LDF6810ST Stainless Steel Built-in Dishwasher

1 Answer

I'm getting an error code LE on the control panel and there is still water in the bottom of the dishwasher. The cycle was almost finished. What is the problem?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 6,784 Answers

This is a drainage issue. check the following to address this issue.

1. Air gap / Drain hoses
If there is an air gap (located in the sink, near the faucet), check to see if it is clogged. Unscrew the top cap and see if there is anything blocking inside. Note: If there is no air gap installed, the dishwasher might not drain properly.

If the drain hose is clogged, the dishwasher would not drain. If there is an air gap installed, it is very common that a hose going from the air gap into the garbage disposer is clogged. Remove and clean the hose. Make sure to reattach the hose before starting the dishwasher.

Note: If you recently had a garbage disposer installed, it is common to overlook removing the drain plug.

2. Broken belt
Some dishwasher models use a belt to drive the pump. Replace the belt if found broken.

Note: Sometimes the belt would just come off the pump. Even though it might not be broken, it is recommended that you replace the belt, because it is probably too stretched out.

3. Pump
Some models have two impellers inside the pump - one, wash impeller, takes care of the wash cycles, the other, drain impeller, drains the water out. If the drain impeller is broken (broken blades, shaft), the dishwasher would not drain. Replace any broken pump components.

4. Drain solenoid
Some models (for example most GE dishwashers) use a drain solenoid to drain water out. Sometimes the solenoid gets stuck, preventing the water from draining out. Try to free up the solenoid. If unsuccessful, you might have to replace the pump assembly.

5. Motor
If the motor is stuck, it is sometimes possible to free it up by manually spinning the motor.

Replace the motor if defective.

6. Timer
Replace if defective (note: uncommon problem).


Posted on Jun 26, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Kid 60 s10 please give fault codes


Hi Roger, Hope this helps......CHEERS..

KENMORE DISHWASHER ERROR CODES

Kenmore Dishwasher Error Code = Start Resume light blinking slow
When the dishwasher door opens or electrical power is removed during the cycle then the dishwasher will not start again. The door is detected as being closed and the Start Resume button is being pressed
Kenmore Dishwasher Error Code = Clean light is blinking 7 times
Heater circuit fail. Control panel did not detect the water getting hot. Did not detect heating element was energized to heat the water during the wash cycle
Kenmore Dishwasher Error Code = Sanitize LED blinking at end of cycle
Control panel could not detect if sanitation has been achieved
Kenmore Dishwasher Error Code = Console light blinking rapidly
There is a stuck button on the control panel
Kenmore Dishwasher Error Code = Clean light is constantly illuminated
Dishwasher cannot start a wash cycle until it sees that the door has been opened after the previous washing cycle
Kenmore Dishwasher Error Code = Control lock LED is ON but not responding to pressing of the keys
Turned on by accident or there is a control detected key pad problem

Mar 31, 2016 | Kenmore Dishwashers

1 Answer

HOW TO FIX LE ERROR CODE ON SAMSUNG DISHWASHER DMR78AHS


An LE error code on your dishwasher stands for "LEaking."

There is, what I call, a drip pan on the bottom that the water is dripping into. Remove your dishwasher and take off the lower the side panels to get a look inside the drip pan. If you have water in there, try to find out where it's coming from.

If there are no signs of water, tip the dishwasher over on its side and remove the plastic panel on the bottom of the dishwasher. Once removed, you can disconnect the connector to the leak sensor (it's mounted upside-down, with 4 wires coming out of it. If I remember right, the wires are blue and red).

Flip the dishwasher back upright and plug it in and see if your LE error code pops back on. If it pops back on, then you have a bad board. If it doesn't, then you either have a leak, or the "fangs" on the leak detector are shorting out, somehow.

Good luck!

Oct 29, 2014 | Samsung Dishwashers

1 Answer

LG dishwasher error code after 2 minutes


fault with the programe as it has stoped in mid cycle

Aug 01, 2012 | Whirlpool Dishwashers

1 Answer

My new bosch axxis washer was20160uc does not start


Open the dishwasher door if the desired cycle does not perform as selected on the control panel. Press the main power switch "Off" and then "On" again. Select a cycle, press the appropriate button, press "Start" and close the door. Make sure the door is closed completely.

Check the circuit breaker and water supply if the dishwasher does not start after selecting the appropriate cycle on the control panel and shutting the door.

Turn "Off" the dishwasher and disconnect the dishwasher from the power supply if an error code between "E01" and "E30" appears on the digital display. Reconnect and turn the dishwasher "On." This should reset the control panel.

Terminate a program on the control panel by holding the "A" button and pressing "Start" at the same time. The display will read "0:01". Close the door to start the program sequence. The display will read "0:00" when finished.

Oct 15, 2010 | Dishwashers

2 Answers

I get an LE error message on my LG Dishwasher. I replaced the pump. Still get the LE error. Replaced the main control. Still get the LE. No blockage in the pump. What now?


When you receive the LE error code, unplug the machine for approximately 15 - 20 minutes. This will reset the microprocessor.

Oversudsing is the main cause of LE error codes. Using non-HE detergents or too much detergent will cause stress on the motor. Oversudsing can also cause leaking and odor.

A breakdown in the signal between the microprocessor and the motor may cause the error code. This can occur if there is a loose wire.

A couple of notes about this - there are at least three motors on this unit - the main pump, the drain pump, and the 'vario motor' which appears to control the direction of water flow through the sprayers. The main pump is the one likely to go bad. Another cause of the LE code is broken wires in the door. The wires in the door get stuck in the black sound insulation and eventually break. Sometimes, this causes the LE error code. Check the wires in the door first. They are located behind the large front panel. It's easily removed by undoing 6 screws.

Sep 06, 2010 | Dishwashers

1 Answer

Dishwashing cycle starts for about 3 minutes then flashing LE light comes on and the machine stops. Why?


Display Condition LE = Motor Error

Possible Cause For Error Occurrence:

Wiring connection is OK?
The Impeller of Washing Pump is locked.
The rotor of Washing Motor is locked.
The Blade is locked.


Remedy:

Check the wiring connection.
Replace the cause of restriction.
Replace the Washing Motor.
Replace the PCB.

Try the following steps:

Unplug the washing machine if you see an LE error on the two-digit display electronic readout. This error indicates a miscommunication between the control panel and wash motor.

Press and hold the "Start/Pause" button on the front panel for five seconds.

Plug the LG dishwasher back in.

Run a cycle. The LE code will clear.

Aug 31, 2010 | LG 24 in. LDF 7811 Stainless Steel...

2 Answers

My Asko dishwasher is not draining. Code F2


drain plugged, hose kinked or discharge pump bad

Jan 19, 2010 | Asko D1976 Built-in Dishwasher

1 Answer

"LE" Error Code appears on control panel


LE is a motor error Wiring connection is OK? The Impeller of Washing Pump is locked. The rotor of Washing Motor is locked. The Blade is locked. REMEDY Check the wiring connection. Replace the cause of restriction. Replace the Washing Motor. Replace the PCB.

Sep 24, 2009 | LG 24" Built-In Dishwasher - Black

1 Answer

Error LE on display of a LG dishwasher model LDF 6180WW Leaves water in the bottom of unit


Hi there,

Well LE means locked motor, this seems to be a very common problem withe these dishwashers.

Possible Cause For Error Occurrence:
Wiring connection is OK?
The Impeller of Washing Pump is locked.
The rotor of Washing Motor is locked.
The Blade is locked.

Anyway the LE error code is not all-ways indicative of a motor problem. There are also strong chances of any lose connection (wire), so first you can simply unscrew the front door panel from the retaining screws on the inside of the perimeter of the door. Once the screws are removed pull down and out to remove the door panel. Remove the sound insulating material and you will see several wires routed from the contol panel the length of the door to underneath the unit. Inspect the wires thoroughly. Near the bottom is where the pinching can take place. There are two gray wires and if you have been getting the "LE" error code, one of those wires is most likely broken or pinched. Splice, reconnect, solder or tape.......

Please follow the below link for more information (the link contain service manual, you can check the page number 25) -

http://136.166.4.200/contents/Dishwasher/LDS5811/LDS5811_Service_Manual.pdf

(Just copy and past the above link in your web browser)

Thanks

Jun 27, 2008 | Dishwashers

1 Answer

LE ERROR CODE


This new....just call out LG to repair under warenty!!

Jul 22, 2007 | LG LDF6810 Built-in Dishwasher

Not finding what you are looking for?
LG LDF6810ST Stainless Steel Built-in Dishwasher Logo

470 people viewed this question

Ask a Question

Usually answered in minutes!

Top LG Dishwashers Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Mike

Level 3 Expert

4336 Answers

Les Dickinson
Les Dickinson

Level 3 Expert

18392 Answers

Are you a LG Dishwasher Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...