Question about Ovens

1 Answer

How do you fit a bayonnet gas hose

The cooker comes with a male thread yet all standed gas bayonnet hoses come with a male thread to fit a female thread on the coooker?

Posted by on


1 Answer

  • Level 1:

    An expert who has achieved level 1.


    An expert who has answered 20 questions.


    An expert that has over 10 points.


    An expert whose answer got voted for 2 times.

  • Contributor
  • 34 Answers






Posted on Nov 05, 2007


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Imperial oven will light but will go off when you turn on more than two Cooker burners. What could be the cause ?

this is usually and indication of a gas issue. either a gas pressure issue or the cut off valve not open all the way, or the hose connection is not completely on if it is a snap-on type.

Mar 01, 2017 | Imperial Ovens

1 Answer

My display is broken so I cant put oven on any advice

Had a similar problem over a year ago on my Rangemaster, neither of the ovens would come on, only the gas hob worked.
The cost of a new display unit was around £100 plus so decided to check out the unit by removing it (it was quite easy to do; but remember to isloate the cooker from the mains before you start dismantling).
On my display there were six wires plugged into it. I marked each one and the display before removing them so that they all went back to the correct location (i am not an electrician and am therefore an electrical numpty).
Firstly I degreased each male and female connector using an electrical spray degreaser/cleaner and then cleaned them using very fine emery paper and a special pen with glassfibre bristles until they gleamed and then gave them a final spray to remove any debrie left by the cleaning process.
Before i put everything back i also cleaned all the connectors to the switches etc which were accessable in a similar manner; about another eight/ten in total.
Following reassembly and switching the power back everything started working again. All this work took about an hour and my cooker has been working fine for the last 12 months.

Nov 16, 2014 | Ovens

1 Answer

Showing f3 high on display

F3 stands for a faulty oven sensor. Unplug the oven, then replace the sensor. Should be back to normal. The sensor is inside the oven. When you pull on the sensor, you'll get to a male/female quick connector. When you unplug it, be careful not to lose the other end behind the oven wall or this simple repair won't be so simple anymore. Check here the replacement sensor for your oven.

Hope this helps.

Jun 14, 2011 | Ovens

2 Answers

What does it mean when a gas cooker needs hardwiring

It means that it does not have a cord and a plug to just plug it into a wall socket...
It needs to be "hardwired" into the electrical circuit with a regular piece of wire...


Dec 13, 2010 | New World G60m Gas Single Oven

1 Answer

I have a cooker with a bayonet fitting that wan't connect the the wall because the wall has a screw fitting what part do i need to connect the cooker to this ?

You need to check with your hardware store and get a fitting compatible with your fitting on the stove.This will have to be fitted to the wall pipe but I stress that this should only be carried out by a registered gas fitter.

Hope this helped.

May 07, 2010 | Ovens

3 Answers

The water fills and drain from the bottom of the washing machine. Have checked all the pipes no problem. Please advice

front load or top ? drain hose must be elevated to 36 '' 34 min. if hose on floor it will not work .. needs stand pipe . if its leaking inside you may have a hose off . reinstall and wala it works .. mm hope some of ans work for you ..

Dec 03, 2009 | Ovens

1 Answer

Gas connection on bottom of oven does not accept std 1/2'' flex hose?

all gas connections are flair fittings if the 1/2 inch is to large a 3/8 inch is the mext size down. if the 1/2 is too small the next size up is 5/8

Sep 03, 2009 | Frigidaire 24" Single Gas Wall Oven with...

2 Answers

Beko D533 cooker only half working

where the power goes in there should be fuse links on both sides if they all in then its the thermal fuse inside

Dec 07, 2008 | Ovens

6 Answers

Leisure rangemaster 55 gas cooker

It sounds exactly the same as I am experiencing on my oven of the same model. My theory is that the full flame gas is controlled by a thermostat, and that this has broken hence why the oven only stays on preheat. This will be a matter of a replacement part. Most likely the thermostat is a bi-metal strip that, because it has heated and cooled so many times in it's life it has simply finally given up. Try searching online for the correct part and get a corgi registered fitter or another suitably qualified fitter to come and replace it.

Nov 13, 2007 | Ovens

Not finding what you are looking for?
Ovens Logo

Related Topics:

733 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ovens Experts

Dan Webster
Dan Webster

Level 3 Expert

8220 Answers


Level 3 Expert

417 Answers


Level 3 Expert

77932 Answers

Are you an Oven Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides