Question about Xante CL30 HSE Laser Printer

1 Answer

CL30 color banding

Trying to obtain smooth, full coverage. We always get some kind of banding or have issues when we try to do big blocks of color. We are looking to find a stock that could run through xante Cl30 easy, be heavy weight, AND allow for smoother coverage.

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 6 Answers
Re: CL30 color banding

Banding is often caused by light shock to the drums, caused when the printer is left open too long. This may cause permanent drum sensitivity that will not go away until you instal new drums. You may also find that the banding goes away after you get into a longer run, if it is just the "parked" position of the drums giving you a bad "first copy"

Posted on May 28, 2008

Add Your Answer

0 characters

Uploading: 0%


Complete. Click "Add" to insert your video. Add


3 Points

Related Questions:

1 Answer

Transfer belt error 356

there is what is called a etb electron static transfer belt in this system if that is what you are referring to then it will be a big cost to six. but if the etb belt ids warn then that might be why it's life was so short

May 15, 2010 | Xante CL30 HSE Laser Printer

1 Answer

How do i stop banding on hp9000 -- i print a job of 25' long first 8' or so print passable - little banding - so i walk away for about 10 mins or so - several feet comes out thick banding lines --ex. my...

The reason for banding on the long panels (especially with solid coverage) is the high content of dissolved air in the ink. Dissolved air causes a gradual nozzle drop-out that cannot be stopped unless you do the head cleaning in the middle of the print. Unfortunately you cannot force HP9000 to do the automatic head cleaning in the middle, it can do it only at the end. Manual head cleaning is possible but it takes such a long time that it shows as stripe on a print, and the productivity suffers. Even the OEM HP ink is full of air inside. Our company did a lot of research in this area and we came up with a special ink packaging technique that ensures the ink is 100% free of air. People who tried printing with our ink can easily print 50-foot panels without any nozzle drop-outs or color shift. If you want more info please call us at 1-905-820-8833, We also produce portable print head recovery devices and solutions for solvent printer recovery after long periods of inactivity.
Vladimir Digital Sign Technologies

Feb 26, 2010 | HP DesignJet 9000 InkJet Printer

1 Answer

Do not print full cover page

Have you tried the Transfer Unit.? That is what transfers the ink to the paper before it is fused by the fuser.

I would guess Trasfer Unit if it is all colors.. If it is one colr then maybe laser unit.

Jun 30, 2009 | Xerox Phaser 7400/DXF Laser Printer

2 Answers


in photoshop or MS word just increase the contrast of the image and all dirty gray background will disappear and if u need our technician support contact

Jun 22, 2009 | Xante CL30 HSE Laser Printer

1 Answer

Hey m8

  • Buxie, first off you have voided your warrenty, secondly
  • If marks repeatedly appear on the printed side of the
    page at even intervals:
    • Clean the inside of the printer. See “Cleaning the
    Inside of the Printer” on page 5.7. After cleaning
    the inside of the printer, if you still have the same
    problems, install a new toner cartridge of the
    problem color. See “Replacing Toner Cartridges” on
    page 5.3.
    • Parts of the printer may have toner on them. If the
    defects occur on the back of the page, the problem
    will likely correct itself after a few more pages.
    • The fusing assembly may be damaged. Contact a
    service representative.
  • If horizontally aligned color or black streaks or
    smears appear:
    • A toner cartridge may be installed improperly.
    Remove the toner cartridge and reinsert.
    • A toner cartridge may be defective. Install a new
    toner cartridge.
    • If the problem persists, the printer may require
    repair. Contact a service representative.
  • SXPRESS- It is normal to have to replace it after that because the starter cartridges are rated for 1500 pages but that is at only 5% page coverage and most people print alot higher coverage than that, and the replacements cover 2000 pages again @ 5% page Coverage

May 20, 2008 | Samsung CLP 300 Laser Printer

2 Answers

Xante cl30 color laser printer paper jam

Remove the fuser and examine it closely (Note: the fuser gets extremely hot. Wait until it has cooled completely before touching it!) Paper or a paper fragment might be balled up inside it.

Even just re-seating the fuser might clear the sensor that is reporting this jam.

If the printer continues to stall with this error code, even though there is no jam, it could have a faulty sensor. This would have to be repaired with a service call...

Mar 06, 2008 | Xante CL30 HSE Laser Printer

2 Answers


"Carrier stall" Error and the Carrier Slams in the Printer ID:ENUS12078 null.gif null.gif null.gif
If the printer carrier is slamming into the side of the printer, please try the following:
  1. Disconnect the power supply from the back of the printer.
  2. Open the front cover of the printer where the cartridges are located.
  3. Look for two black bands that span from left to right (they should have one serrated side and one smooth side). Just above the black bands there is a transparent strip; this strip is called the Encoder strip.
  4. Flick this strip lightly with your finger to make sure that it is running smoothly from left to right. You may need to do this two or three times. CAUTION: Do not pull the strip!
  5. Close the front cover of the printer and reconnect the power supply.
  6. If the problem persists, you may need to contact Lexmark Technical Support.

Oct 26, 2007 | Lexmark X1150 All-In-One InkJet Printer

2 Answers

Red is printing pink.

have u used this printer quite a bit....? if so the following may be the problem and I just did run across this recently in a printer we had in the shop....I recently read in one of my technical magazines that there may be a design flaw in the placement of the laser scanners and the openings that protect seems that excess toner dust can readily get in to scanner area and specifically inside the scanner assembly and accumalate on the scanner glass and lens. Just cleaning through the opening in the back of the printer will not eliminate the issue. Machine will have to be disassembled, scanner removed and opened and the glass/lens cleaned with a q-tip....the placement of the fan (behind cartridges, lower right) seems to speed this process up and it usually becomes first notable with the magenta cartridge, seeing as it is at the bottom of the printer closest to the fan. Hope this helps..


Oct 04, 2007 | HP Color LaserJet 2600n Printer

1 Answer

Poor registration on Xante CL30 HSE

Make sure the drums are properly seated in their cradels, and if posible, avoid designing with white small text in heavy solid areas that are made up of process colours. For reverse type in a black background, use spot color black rather than rich black. Other than than printing on a not as heavy card, that is about all you can do.

Aug 19, 2007 | Xante CL30 HSE Laser Printer

Not finding what you are looking for?
Xante CL30 HSE Laser Printer Logo

Related Topics:

211 people viewed this question

Ask a Question

Usually answered in minutes!

Top Xante Printers & Copiers Experts


Level 2 Expert

197 Answers

john archer

Level 2 Expert

186 Answers


Level 3 Expert

56925 Answers

Are you a Xante Printer and Copier Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides