Question about Hotpoint NBXR463EBWW Electric Dryer

1 Answer

How to change dryer belt on Asko 7305 dryer

How do i change the dryer belt on Asko 7305 dryer

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.


    An expert whose answer got voted for 2 times.

  • Contributor
  • 1 Answer
Re: how to change dryer belt on Asko 7305 dryer

You have to pull the back off the dryer.Then you,ll be able to see how it comes off.Ussally its on two pulleys similar to a car.There may be a tensioner on it to to keep it from slipping.If there is one you,ll have to losen it to remove the belt & replace it,then tighten the tensioner back up.Ussally you keep about a 1/4" to 1/2" free play on the belt.You use a sraight edge on the two pulleys to measure it with the belt on,tighten belt tensioner till you have the recommended tighteness.

Posted on Feb 19, 2008

Add Your Answer

0 characters

Uploading: 0%


Complete. Click "Add" to insert your video. Add


3 Points

Related Questions:

1 Answer

I have a Asko 7305 dryer,can I have a regular 240volt dryer cord put on it, so I can use existing wall receptacle ?

I think you are asking if you can change the cord from 220 amp to 110 amp so you can use a 110 wall receptacle...NO you cannot not.It would also probably start a fire

May 13, 2015 | Asko Dryers

1 Answer

F5 code on Asko 7305, can humidity sensor be bypassed?

I've had luck vacuuming the lint and dust out of the humidity sensor on my Asko. Suggest trying that first. While you're in there you might also exercise the connectors at the circuit board end of the sensor's cable(s). If they're corroded, some simple unplugging and replugging a few times might burnish the connectors. I've observed that our dryer will sometimes run longer than necessary on days when the relative humidity is high. Not very often but enough to suspect a trend. If your environmental air is humid, I would wonder if you're experiencing a similar condition. Every couple of years I take the dryer outside and blow it out with the air compressor: air chamber including heater coils as well as all the innards. This also gives me a chance to keep an eye on the belt!

Dec 23, 2013 | Asko Dryers

1 Answer

I need a power plug for my asko 7305 dryer and can not find one anywhere

Assuming that you need a 220V connector, they can be purchased at home Depot. They are generally made with about three feet of cable attached. you will have to take the back plate off of the dryer and attach the three leads to the proper termination.

Jan 23, 2011 | Asko Dryers

1 Answer

How do I change the power cord on my asko 7305 dryer?


Here is a tip that will help you with changing your dryer plug.

Dryer Cord and Wiring Dryer 3 Wire or 4 Wire


Dec 29, 2010 | Hotpoint NBXR463EBWW Electric Dryer

1 Answer

When drying a load of clothes the dryer (Asko 7305) simply quit and when I came back to the unit the clothes were dry, but the digital panel was dark and no power available to the unit. I have pushed the...

Hello Susan, Welcome to FixYa. Have you checked to see if perhaps one or both of the fuses may have blown at the back of the unit...I don't mean the hi-limit that you already referred to...I mean the in-line fuses the Asko machines are equipped with. Let me know and we can move forward from here. Regards, Macmarkus :)

Sep 12, 2010 | Asko T761 Electric Dryer

1 Answer

Model 7305 - power light comes on when switch is pushed but none of the cycle lights or Start button come on when buttons are pushed

Problem was solved by pushing the very hard to find black reset button in the center of the back of the dryer.

Feb 22, 2010 | Asko Dryers

1 Answer

I need a rubber gasket that goes around the lint filter on an Asko 7305. It is available? If so, what is the price delivered to California. Thanks.

Go to the part you need is around $15 and the shipping is good on that site I have bought alot of items from them and are great dealer .....

Nov 17, 2009 | Asko Dryers

1 Answer

Asko 7305 dryer keeps tripping out hi-limit on back of unit please help

make sure that the heating element is not shorted to the cabinet. Usually when you replace the hi limit you should replace the thermastate along with it. What is the brand of the dryer?

Jan 04, 2009 | Dryers

Not finding what you are looking for?
Hotpoint NBXR463EBWW Electric Dryer Logo

930 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hotpoint Dryers Experts

Gerry Harvey
Gerry Harvey

Level 3 Expert

1456 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Chris Hall
Chris Hall

Level 3 Expert

842 Answers

Are you a Hotpoint Dryer Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides