Question about Washing Machines

2 Answers

Error codes My washer dryer keeps coming up with e20 error code during the cycle of washing or drying i can't find a manual with the error codes, i have cleaned the filter so i know it can't be fluff. I would appreciate any suggestions or the error codes. Thanks Washing machine Daewoo Lavadora DWD-F1011 stops working after 10-15 minutes of "normal" washing and displays error code F9 and F2 trying to drain the water. Cannot find what th error codes mean.

Posted by on

2 Answers

Re: error codes

If this is a fridgidaire washer, I guess it's a clogged coin catcher. You have remove the front access panel and clean it out. I am working on that now.

Posted on Dec 01, 2007

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer
Re: error codes

My Kenmore H3 stops working, starts beeping and flashing "F9", but it only happens when I'm washing a heavy load like jeans or bath towels. I think it gets off-balance and I have found that if I hit "pause" once and then hold in "start" briefly it somehow resets itself and works fine from then on till the load is completely done.

Posted on Feb 22, 2008

Add Your Answer

0 characters

Uploading: 0%


Complete. Click "Add" to insert your video. Add


3 Points

Related Questions:

1 Answer

Error code E20 on a AEG washer dryer

Ok if its only bring the E20 up on the drying side then this will be a blocked dryer condenser chamber.

To get at this you need to take the back half of the washer off and from there you will see a big plastic chamber going from the bottom up to the top.

Take this chamber off and give it a good clean out with a hose pipe.

Once this is clear refit it and the dryer should be back to normal from there.

Oct 14, 2012 | Washing Machines

1 Answer

Error code E20 comes on during a wash cycle. i

If the filter is clean and the hoses are free of obstructions,you will need to replace the pump

Oct 18, 2009 | Washing Machines

1 Answer

Error E20 showing ........stops during wash cycle and clothes not dry on drying cycle

not familar with the code but usually wash has a built in thermo stop to wait for water to heat to correct temp,if it works normally in a rince cycle and spins out and finishes properly i would look at heat element or stat,hope this helps

Apr 06, 2009 | Zanussi ZJD1219 Front Load Washer / Dryer

1 Answer

AEG Lavamat Turbo 12830 - error code E20


E20 means there is a bolckage in there
remove filter and clear any debris in there and check impeller is turning ok.


Mar 21, 2009 | AEG Lavamat 16810 Front Load Washer/Dryer

1 Answer

Error codes

If this machine is like other of its type then you may find the manual taped to the inside of the machine near the bottom side panel.
open the bottom access panel (3 screws on bottom front lip) and look for it as it will have the codes. near where the filter is .
while you were down there cleaning the filter did you check that the pump impellers move freely and were not clogged with any debris.

Jan 28, 2008 | Maytag EPIC MFW9700S Front Load Washer

2 Answers

Error codes

I suggest you snake out the drain into which the machine waste hose goes, the standpipe that is. The drain could be blocked somewhere causing pressure problems which is conveyed to the machine. Be sure to replace the machine exit hose at about 3 feet from ground level, and dont shove it too much into the standpipe. Do not block up the point where the machine hose goes into the standpipe, it shouldn't be air tight.

Dec 28, 2007 | Frigidaire FTF530FS Front Load Washer

3 Answers

E20 message

Hi Helenw,
The error message E20, simply means the filter plastic cage which is located behind the trap door bottom right side of the machine is full and needs to be cleaned out.
All the fibres and lint gets trapped in here and prevents the waste water from escaping, hence Error code E20.


Sep 12, 2007 | Zanussi WJS1265W Front Load Washer/Dryer

2 Answers

"CD" ERROR ON LG WM-3677HW Front Load All-in-One Washer / Dryer

CD means cool down, press the pause start button, the door lock will open. It is an anti crease cycle. It mentions it in the owners manual, but it is hidden deep in the drying section.
Sgt 48

Sep 01, 2007 | LG WM-3677HW Front Load Washer / Dryer

2 Answers

Error codes

Hello ALARM CODES Alarm code Description of fault User code Effect E11 Problems with water fill in wash phase E10 Cycle PAUSED 8.2 E12 Problems with water fill in drying E10 Cycle PAUSED 8.3 E21 Problems with water drain in wash phase E20 Cycle PAUSED 8.4 E22 Problems with water drain during drying or drying condenser blocked E20 Heating phase skipped 8.5 E31 Analogic (electronic) pressure switch circuit faulty --- Cycle blocked with door closed 8.6 E32 Incorrect calibration of analogic (electronic) pressure switch --- Cycle PAUSED 8.7 E33 Incongruency between level of analogic (electronic) pressure switch and level of anti-boiling pressure switch 1 --- Cycle blocked with door closed 8.8 E34 Incongruency between level of electronic pressure switch and level of anti-boiling pressure switch 2 --- Cycle blocked with door closed 8.9 E35 Water level too high --- Cycle blocked with door closed and water drain 8.10 E36 "Sensing" circuit of anti-boiling pressure switch 1 faulty --- Cycle blocked with door closed 8.11 E37 "Sensing" circuit of anti-boiling pressure switch 2 faulty --- Cycle blocked with door closed 8.11 E38 Pressure chamber blocked --- Heating phase skipped 8.12 E41 Door open E40 Cycle PAUSED 8.13-14 E42 Problems with door closure E40 Cycle PAUSED 8.15-16 E43 TRIAC which powers the door interlock faulty E40 Cycle PAUSED 8.17-18 E44 "Sensing" circuit of door delay interlock faulty --- Cycle blocked 8.19 E45 "Sensing" circuit of door delay interlock triac faulty --- Cycle blocked with door closed 8.19 E51 TRIAC which powers the motor short-circuited --- Cycle blocked with door closed (after 5 attempts) 8.20 E52 No signal from tachometric generator --- Cycle blocked with door closed (after 5 attempts) 8.21-22 E53 "Sensing" circuit of motor TRIAC faulty --- Cycle blocked with door closed 8.23 E54 Relays (motor) contacts faulty --- Cycle blocked with door closed (after 5 attempts) 8.23 E61 Insufficient heating during washing --- Heating phase skipped 8.24 E62 Overheating during washing --- Drain, end of cycle 8.25 E63 Insufficient heating during drying Heating phase skipped 8.26 E64 Overheating during drying --- Heating phase skipped 8.27 E66 Power relay to heating element faulty --- Drain, end of cycle 8.28 E71 NTC wash sensor faulty --- Heating phase skipped 8.29 E72 NTC sensor on drying condenser faulty --- Heating phase skipped 8.30 E73 NTC sensor on drying duct faulty --- Heating phase skipped 8.31 E84 "Sensing" circuit on circulation pump triac faulty --- Drain, end of cycle (door open) 8.32 E85 Circulation pump faulty --- Drain, end of cycle (door open) 8.33 E91 Communications error between main PCB and user interface --- --- 8.34 E93 Configuration error E90 Cycle blocked 8.34 E94 Incorrect configuration of washing cycle E90 Cycle blocked 8.34 EF1 Drain filter blocked LED-EF0 --- 8.35 EF2 Excessive detergent LED-EF0 --- 8.35 Regards David Marsh

May 06, 2007 | Zanussi ZWD1470W Front Load Washer / Dryer

1 Answer

Error code 20

Hi, I also got the error code E20 when the filter became totally blocked during the washing cycle (due to a pair of my son's old work jeans!). Once I cleaned out the filter everything worked ok again. Put a large bowl under the filter as you unscrew it; a fair amount of water could be there. Regards, John

Sep 04, 2006 | Zanussi ZJD1219 Front Load Washer / Dryer

Not finding what you are looking for?
Washing Machines Logo

Related Topics:

1,948 people viewed this question

Ask a Question

Usually answered in minutes!

Top Washing Machines Experts

Dan Webster
Dan Webster

Level 3 Expert

8147 Answers

Richard Roth
Richard Roth

Level 3 Expert

9472 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Are you a Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides