Question about Grinders

1 Answer

Ryobi Bench Grinder with Linisher tracking difficulty.

I have a Ryobi Bench Grinder with Linisher HBGL650. I'm having great difficulty getting the sanding belt on the Linisher to track safely and successfully. It always wants to move to the left and foul the metal tabs on the left hand side. Often the Top pulley just comes flying loose, very dangerous.

It seems to me that the pivot points (dimples) on the metal ''L''-shaped part are too far ''north'' and the movement of the Belt Tracking Knob has too little effect. Can you please assist me.

Bob

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,714 Answers

It sounds like the pulley is not adjusted correctly. This is causing the belt to move on you. Carefully inspect and adjust the pulley so it is square and flat. Use a straight edge.

Posted on Jun 26, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a Ryobi bench grinder and the grinding belt keeps slipping to one side have tightened to maximum and the belt says its for a Ryobi


it is slipping to one side because the pulley on the end is not aligned correctly
on the adjuster arm that holds the front pulley there is a lever or knob that you use to adjust alignment ( instructions in user manual) find that adjustment and slowly move it while the belt is running
you will see the belt running position change to you get it properly aligned
each belt regardless of ryobi or generic will need adjustment after fitting

Nov 27, 2016 | Bench Grinders

1 Answer

Wher can i get a output shaft for a ryobi EAG95100angle grinder 900w


go google and type in--- parts for ryobi 4 " angle grinder model eag 95
I recently spent may hours searching for parts for ryobi angle grinder 4" that is close to 45 years old and saw plenty of sites for ryobi and others that carried listings for many ryobi grinders
I suspect that you will be lucky as you have a model where as I didn't have that luxury

Jul 08, 2016 | Ryobi Saws

1 Answer

How to change a grinder blade on a ryobi grinder


Handheld grinder or bench grinder? I'll assume you're asking about a handheld grinder.

Engage the arbor lock. You may need to rotate the wheel until you find the spot where the arbor lock locks the wheel. Use a wrench or a gloved hand to unscrew the wheel (I use my bare hand). Screw the replacement wheel on and disengage the arbor lock. The new wheel doesn't need to be very tight, it'll tighten itself as you work.

Jul 15, 2014 | Saws

1 Answer

Is there an overheat shut off


It is very posible and a good thing to have. It is there to protect the motor windings from over heating and causing the motor to fail.

May 16, 2014 | Ryobi Grinder. 6 in. Bench Grinder BGH6110

1 Answer

I need a Dianz cbb60 mkp sh 8uf capacitor for a ryobi bench grinder.


you can get these at any ac/heating parts houses such as ferguson rsd or allied...you will need to have contractors license to purchase from these parts houses...try getting one online

Oct 21, 2013 | Heating & Cooling

1 Answer

Have 25 year old Wilton belt grinder. Belts seem to wobble when running then will just not track. Not sure what part needs replacement.


The motor and grinder pulleys need to be perfectly parallel or the belt will track to one side or the other. The belt must be uniform with no stretch or wear points which will cause erratic travel. Hope this helps!

Nov 09, 2010 | Wilton Variable Speed Wheel Grinder, Bench...

1 Answer

17202 8'' bench grinder 3yrs old hasent run 1 hr needs on off switch wilton stated after 6mos of waiting for soposed back order that co that maid these for wilton is out of business they said try lowe;s...


go to your local marina and buy a simple on off switch or take the wires off the switch on your grinder and hook them up to a extension cord and put an inline light switch on the cord.

Oct 21, 2010 | Wilton 17202 8" Bench Grinder

1 Answer

I have an Abbott & Ashby 200mm Industrial Bench Grinder - CS-8GCM I need to change the sanding belt and am unsure how to do it, can you help?


Remove/open cover on the right side of belt assembly housing. push downward on tracking knob left side top of unit.Belt is spring tensioned to remove slack.Push down remove old belt,push down again for new belt.With belt running adjust belt track(centering) by turning knob,top of unit,toward or away from you,Arrow on inside of new belt governs direction of rotation of belt.

Jun 09, 2010 | Sander 6" Bench Grinder 2" Belt Combo...

Not finding what you are looking for?
Grinders Logo

Related Topics:

555 people viewed this question

Ask a Question

Usually answered in minutes!

Top Grinders Experts

Pieter Vleeshouwers
Pieter Vleeshouwers

Level 3 Expert

1793 Answers

Lawrence Oravetz

Level 3 Expert

9587 Answers

Vernon Taylor

Level 3 Expert

3194 Answers

Are you a Grinder Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...