Question about GE WBSR3140DW Top Load Washer
Ge washer wjrr4170e6ww does nothing but wash and drain. the knob striped cheap plastic can still select settings. worked fine that way now have just wash and drain. all my selection are gone no matter where i put it. motor inverter board ststus code reads normal. i think it is cheap plastic gears in the timer asm (ps270259) i could use a little solving this thank you.
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
Here's a link to this great service
Posted on Jan 02, 2017
SOURCE: GE Washer won't drain or spin
this is something that you can fix even if your not a technical person . first you have to open the washing machine front panel or back panel , second , follow the DRAIN HOSE to where its connected to a little motor, disconnect the DRAIN HOSE , take the LITTLE MOTOR out and clean it out , it could be clogged.
it happen once and find out the person put the BATH RUG SET
to wash , the rug was so old that pieces of a rubber underneath the rugs clogged the drain , so there was no rinse and no spin.
try it , I hope it helps.
Posted on Apr 16, 2008
SOURCE: Drain pump/motor not draining.
actually it sounds like there was or is something in the water pump (like a string or metal underwire from a bra). before replacing the water pump i would look inside it and check for foreign objects.
some pictures borrowed from fixitnow.com, allpar.com, applianceaid.com and repairclinic.com
let me know if you get stuck
Posted on Jul 30, 2008
SOURCE: Broken knob on GE washer
There are four separate parts that make up the knob dial. You can pull off the knob if you use a screwdriver/pliers to remove the clip holding it on. Check if the mounting areas appear stripped or broken. There should also be a compression ring in the mounting hole on the back of the knob. That's what may be broken or stripped. These are all parts that you can get from a local parts store (check the phone book) and you can do it yourself. Any of those parts should cost less than $10. The bad news is if you stripped the pole coming out of the timer assembly. You would need to replace the entire assembly which costs about $130. If you call a GE repairman, you are looking at $89.95 or more just to have them show up. If it is still under warranty, there is no charge. You can call them to verify this:
Posted on May 03, 2009
This is the electronic washer. Unplug for two minutes, plugin then open and close lid 7 times. This will reset motor. Also make sure belt is not broken.
Posted on Jun 12, 2009
Hello, your problem is going to be with the lids switch, in this machine it is going to be a magnetic contact. You can confirm this my pulling the front panel off and accessing the wireing to the lids switch, If you have electrical knowledge bypass the lid switch using a wire nut and run the machine. If all is ok make sure you relpace the lid switch since it is there for a reason. If you have any other questions or concerns please feel free to comment again. Good Luck!!!
Posted on Jul 19, 2009
Tips for a great answer:
Nov 19, 2017 | GE WJSR4160DWW Top Load Washer
Dec 04, 2010 | GE WHDRR418GWW 35 cu. ft. Washer
Aug 10, 2009 | Washing Machines
Jun 10, 2009 | Whirlpool Washing Machines
Jun 03, 2009 | GE WSXH208A Front Load Washer
Apr 24, 2009 | GE Profile WPRE6100G Top Load Washer
Apr 22, 2009 | GE Washing Machines
Mar 13, 2009 | Washing Machines
Apr 16, 2008 | GE WBSR3140DW Top Load Washer
151 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: