Question about Jacuzzi MAGNUM POOL PUMP 1-1/2 HP MAGNUM PUMP BY

1 Answer

How to disassemble a magnum 1500 - to change the bearing seal.

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 990 Answers

On the big lock ring there is a small clip that you pull out away from the ring then turn out of the way. It is just a peg to stop the ring from turning, with that done from the back of the pump loosten the ring in a counter clockwise direction. With the ring clear start the pump for just a second a couple of times till the water pressure pops the pump in two. Once that is done I beleve it has five screws holding the difuser on, pull that and on most models their is a center screw on the impeller. This screw is a left hand thread so turn it clockwise to loosten it. Then insert something flat and strong in a vain of the impeller on the left side and give it a sharp hit to start the impeller spinning off. If need be spin the rest of the way off and your at the seal. Rember when putting this back together Hand tight only on the impeller and use a teflon or silicone base lube not petroleium jelly.

Posted on Aug 24, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Carvin jacuzzi water pump troubleshooting


How long from the last working of that pump?
Was the Pump stored? unused?
Disassembly and try to make turns the shaft and see if it is Blocked.maybe the bearings are with water and it is rusted.
If the bearings are rusted, the mechanic seal is damaged,you need to change it and the bearings.

Sep 01, 2014 | Carvin Pool Equipment Complete pool pump...

1 Answer

I have a Jacuzzi Magnum 1500 pool. I want to replace the bearing on it. Which bearing size should I buy Motor is a Century Centurion 7-186087-20


Most pool pump motors use 6203 2RS. There are two in each motor. If you haven't done this before I wouldn't attempt it. Once the motors get to a certain age you cannot get the 4 thru bolts out to disassemble the motor. Plus you need a bearing puller. I suggest buying a replacement motor for under $200.00

Jul 29, 2014 | Jacuzzi Pool & Spa

1 Answer

Need to change?? how do I change the bearings and clutch on ac compressor for the 1997 dodge ram 1500 - it has a v8 magnum engine


You need a special puller / installer to remove the clutch on the a/c compressor.... It may be cheaper to pick up a used compressor and swap it out.. You can obtain the re-fill charge cans at most auto part stores and fill it your self.

Feb 12, 2011 | Dodge Ram 1500 Cars & Trucks

1 Answer

How do you change the rear wheel bearings on a 2004 chevy express 1500 van?


Axle Shaft Bearing & Seal Removal & Installation To Remove:
  1. Raise and safely support the vehicle.
  2. Remove the axle shaft.
  3. If replacing only the seal, remove the seal using a suitable seal removal tool.
  4. If replacing the seal and bearing on the 8.6 inch axle, install the slide hammer and adapter behind the bearing and pull out the bearing and seal together.
  5. If replacing the rear axle shaft seal and the bearing on the 9.75 inch axle, install the J 29712 or equivalent bearing puller into the axle housing behind the axle bearing.
  6. Remove the axle shaft seal and the bearing by tightening the nut on the J 29712 bearing puller.
Use a slide hammer, bearing puller and adapter to remove the old axle bearing 88457g81.gif

To Install:
  1. Install the axle shaft bearing using a suitable size driver. Drive the bearing into the housing until the tool bottoms against the tube.
  2. Lubricate the seal lip and install the seal with a suitable seal driver. Make sure the seal is fully seated in the axle tube.
  3. Install the axle shaft.
  4. Fill the rear axle with the correct lubricant.
  5. Lower the vehicle.
prev.gif next.gif

Oct 18, 2010 | 2004 Chevrolet Express

2 Answers

I HAVE A MAGNUM FORCE PUMP. iT WAS RUNNING THIS


It could be the capacitor again, but most likely if it stopped while running, its not that, unless you had a brief power failure. The motor may have a built in thermal overload which turned the pump off. If it only humms then it could either be locked up by something in the impller, or could be the bearings in the motor have failed. If the motor doesn't smell "burnt" then you might stand a change to disassemble the pump. Disassemble the motor and replace bearings. Replace the mechanical seal while you have it apart. OR you could buy a new motor, as it is 10 years old.

Jul 05, 2010 | Jacuzzi MAGNUM POOL PUMP 1-1/2 HP MAGNUM...

1 Answer

On my 2001 Dodge Ram 1500 5.2 2WD, I just found


This is a very simple job to do. Raise the front of truck off the ground,block the rear tires. Using pliers and a hammer,remove the grease cap from hub. Remove the cotter key and nut from axle,pull out slowly and remove outer bearing. then remove hub from axle. To remove inner bearing ,prop hub on a board and use a large punch to drive out bearing and seal. Clean out inside the hub and install new bearing and seal. Replace all parts in the reverse as you took them off. Hope this will help you.

May 14, 2010 | 2001 Dodge Ram 1500 Truck 2WD

1 Answer

I have a Gelatao Magnum Plus that makes a horrible sqeaking noise


Maybe blade assembly it's loose, or bearing are dry, if you can take apart, use grease on the shaft and bearings. or replace motor.

Dec 23, 2009 | Kitchen Appliances - Others

1 Answer

Which valve do I use on the Jacuzzi Magnum 1500 to drain lines


There two plugs on your pump, one one the side of the pot at the bottom and one dead center of the pump housing on the front. this will only drain your pump if you live in cold country and are winterizing you will need to drain all your equiptment filter, heater and any thing else. then you need to drain your pipes and seal them at poolside to keep the water out.

Sep 26, 2009 | Jacuzzi MAGNUM FORCE POOL PUMP - TWO SPEED...

1 Answer

I have a jacuzzi magnum 1500 pool pump which leaks. I changed the O-ring and it still leaks. If I have to change the seal on it, how do I change it. I tried undoing everything on this pump. Thanks!


You need a 201 seal for the pump. Most electric motor shops that work on pumps and of course pool store carry these. If you are unfamiliar with how to change the seal, the charges to have it done are usually low. We charge $15 - $30 depending on how much of the pump is brought in and therefore remains to be taken apart to replace the seal. The seal is about a $5 item.

If trying yourself, you will need to completely disassemble the pump, lock the motor shaft at the rear of the unit, spin off the impeller, and replace both halfs of the seal.

Jun 07, 2009 | Jacuzzi MAGNUM POOL PUMP 1-1/2 HP MAGNUM...

Not finding what you are looking for?
Jacuzzi MAGNUM POOL PUMP 1-1/2 HP MAGNUM PUMP BY Logo

784 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jacuzzi Garden Experts

john h

Level 3 Expert

12104 Answers

Jay Finke
Jay Finke

Level 3 Expert

1338 Answers

Ian Kime
Ian Kime

Level 2 Expert

77 Answers

Are you a Jacuzzi Garden Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...