Question about Kenmore Energy Star 44092 Front Load Washer

1 Answer

Bad shacking during the spin cycle

44092 shakes violently during the spin cycle. Very unstable. I adusted the supports to make the machine level. Did not help.

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that gotĀ 5 achievements.


    An expert whose answer gotĀ voted for 20 times.


    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 146 Answers
Re: Bad shacking during the spin cycle

Remove top of machine and check the centralising springs are still attatched. If springs ok tilt machine against the wall after unplugging from the wall socket and check the shock absorbers. One of them could have jumped out of the guides. If shockies are ok, check the spider for cracks/breaks. The spider is the cast part that holds the outside drum in place. To check this you will have to remove the back plate.

Posted on Nov 05, 2007

Add Your Answer

0 characters

Uploading: 0%


Complete. Click "Add" to insert your video. Add


3 Points

Related Questions:

2 Answers

Washing machine shakes violently during spin


If your washing machine shakes violently or if there's a loud thumping noise during the spin cycle, the load of clothes has probably gotten unbalanced. Open the lid, redistribute the clothes in the washer, then re-start it. Repeat these steps if necessary.

Also check this link bellow:-

May 03, 2011 | KitchenAid Washing Machines

1 Answer

I have an Amana Top Load Washer Model Number ntw4800vq1 The washer shakes violently during the Spin Cylce. It will walk across the floor. I took the console off and removed the outer shell. I checked...


for the question of water comming in the spin cycle, yes its normal we call it a spray rinse. For the shaking check your leveling and also make sure that the back leveling feet when lifting back of washer up and down that the foot mechanism is functining.

Hope this helps

Mar 27, 2011 | Amana Washing Machines

1 Answer

Front loading machine shakes violently during spin

When my washer did that, I found that the shocks that hold the tub were bad...

Check out this tip I wrote about that...

Washer Problems Washer noise when spinning


May 14, 2010 | Washing Machines

2 Answers

Shakes violently during spin cycle from back to

I had this problem with my front loader as well. It is probably the mounts or "level shocks" on the bottom of the unit under the tub. I have a Kenmore by Frigidaire and had to replace the "level shocks". I only paid about $43.00 and was not that hard to put on. Look under your machine and see if the shocks are connected to the tub. Check under the top panel also to see if that particular model has mounts up there too.

Mar 12, 2010 | Maytag NFW7200TW Front Load Washer

1 Answer

Kenmore Whasher shakes on spin cycle

unfortunetly this is common , these new frontloads spin fast even with no pedestal these things move...
make sure the locking nuts for the legs on the pedestal are screwed securely up to frame on pedestal, also could be a floor issue depending on where it is, slooping or not solid floor.

Jan 28, 2010 | Kenmore Elite 45986 Front Load Washer

2 Answers

The drum shakes violently and is very loud during spin cycle

There are 2 shock absorbers/springs attached to the drum. If one of them breaks it will cause a loud banging noise when you wash heavy loads. This is an easy fix. The part is about $22.00 and it is accessed throught the front bottom panel.

Dec 01, 2009 | Frigidaire GLTF1670A Front Load Washer

1 Answer

Kenmore Oasis HE shakes violently during spin cycle

Machine legs should be adjusted so that machine is level and standing on all four legs. The load in the machine should be evenly distributed. Utube has an excellent video on washing machine repair.

Nov 20, 2009 | Kenmore Oasis HE 27082 Top Load Washer

1 Answer

Front load washer shakes violently during spin cycle

On something like this you will need to remove the washer wrap to inspect the suspension springs & base assembly. Please see the link provided for accessing the inside of the washer. Be sure the shipping pins have been removed. The tub should float freely.

Apr 03, 2009 | Washing Machines

3 Answers

Samsung P801 Front Loader shakes violently during spin cycle.

When the washer goes into spin cycle it is suppost to start at a slow speed and continue to increase speed (to a maximum of 800 RPM) as the water leaves the clothes. Your washer is going directly to 800 RPM which causes the washer to shake and stop giving you the E4 code. The control board that controls this speed increase must be replaced.

Feb 23, 2009 | Hotpoint Ultima WD72 Front Load...

Not finding what you are looking for?
Washing Machines Logo

321 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kenmore Washing Machines Experts

Richard Roth
Richard Roth

Level 3 Expert

9472 Answers

Jesus  Colon
Jesus Colon

Level 1 Expert

12 Answers

Fred Sops

Level 2 Expert

271 Answers

Are you a Kenmore Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides