Question about KitchenAid K45SS Classic Stand Mixer

1 Answer

I have a Kitchenaid Professional 5 Plus Mixer beaters won't turn

I have a Kitchenaid Professional 5 Plus Mixer. When I turn on the speed control the motor comes on but the beater does not turn? Can you help me? It is only a year old so, I did not expect problems.

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Dedicated:

    Visited the website for 20 consecutive days.

  • Expert
  • 97 Answers

It sounds like it has been overloaded and the worm gear has been stripped. You will need to take the head apart to confirm this.

Posted on Jan 24, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Kitchenaid mixer will not start


The model number shown is for the Professional series which does not have a separate rear cover. Below are links to KitchenAid mixer Service Manuals:

Professional 5/6 quart
http://ep.yimg.com/ty/cdn/mendingshed/kitchenaid6qtservicemanual.pdf

4.5/5 quart
http://www.kitchenaidparts.eu/documents/pdf/service-manual/classic-svc-manual-new-email-version.pdf

May 13, 2014 | KitchenAid KP26M1X Stand Mixer

1 Answer

Beater is not close enough to bowl


If it is a ksm103 there should be a spring on the shaft, it should look similar to this: http://www.mendingshed.com/kacentershaft.html

When adjusting the screw you should be turning it out, which will make the beater closer to the bottom of the bowl, when properly adjusted you should be able to place a dime in the bowl, and the flat beater should just move it around barely. that would be about 1/16" in clearance.

Mar 06, 2014 | KitchenAid KSM103 Professional 5 Series...

1 Answer

Mixer won't turn on after adjusting beater height


The kitchenaid warranty is exactly 365 days from date of registration "No Questions Asked" on day 366 you have no warranty and you gotta pay.
Now the good news; first check the wall socket, I know it works but check it anyway. then check your plug, did you step on it while you were working on the machine? The plug often falls to the floor during work and can get underfoot, you may have broken the plug it'self. next you will need a parts list for your model from Kitchenaid's website.
http://www.kitchenaid.com/customer-service/manuals/
My first suggestion is to try a minor adjustment of the speed control switch, they often get out of sync when you do something to the machine. You can find several videos of this on the youtube site. "Adjusting the speed control switch on kitchenaid mixer"
If the two or one of the top 2 screws on the speed control switch move it can shut the machine down just like an on/off switch. Did you remove the back cover during your adjustments? Did you remove and replace the carbon brushes on the side of the machine while working on the machine? If you did you might have put them back in incorrectly, if you did they will also act a a shutoff switch. If you did not take them out then DON"T as there are four ways to put the brushes back in and only one way is correct and there are two brushes to deal with. Has work ever been performed on the mixer before? Because if all you did was to adjjust the beater height screw then nothing should have effected the normal operation of the mixer. So if there is anything that you did but did not include in your description of work you performed then please let us know. We strive to give accurate solutions but... as I am a KA tech I do not have any other solutions with out the machine in front of me. Just so you know you can fix this yourself.

May 26, 2013 | KitchenAid KSM150PS Artisan Series Stand...

1 Answer

Kitchenaid mixer motor quit , I dont really see any thing wrong with the brushes.


Obtain a copy of the Repair Part List for your model from Kitchenaid.com.
Download a Copy of the Kitchenaid Service manual.

http://www.kitchenaidparts.be/centers/servicemanual/mixer.pdf

First, you may want to adjust the mixer's speeds:

1. Loosen the lock nuts enough & Turn the 2 top screws clockwise until they cannot be turned
anymore. Leave the bottom screw alone for now.
2. Use a dab of white paint or paper whiteout to mark the positions of the Phillips screws.
3. Plug in your mixer and Set the speed selector to "Stir".
4. Turn each top screw One full turn couterclockwise (alternating between Left and Right)
Keep making one full turn at the time (for both left and right) until the motor starts running.
5. Put your hand near the Agitator shaft and allow it to brush your finger slightly. Use your
watch or clock and start counting the number of times the shaft touches your finger in
60 seconds. The correct count should be 60 RPM (Rounds Per Minute). If it is less
or more than 60, give each screw 1/4 turn counterclockwise or clockwise and start counting
again. Now tighten both lock nuts.
6. Set the speed selector to "6" and turn the bottom screw either clockwise or counterclockwise
to achieve a speed of 180 RPM.

For your reference, the planetary RPM's for the 5-qt. tilt-head Artisan Stand Mixer are as follows:
Stir speed - 60
Speed 2 - 95
Speed 4 - 135
Speed 6 - 180
Speed 8 - 225
Speed 10 - 280

Second, if the mixer won't run:
Remove the Control Plate Assembly (36), the Phase Control Board (39)
and the motor Governor Assembly (35). Inspect for loose connections,
burnt or damaged components. If they seem to look OK, re-assemble
them and test the mixer. If the motor still won't run, then I might suspect
a defective Phase Control Board (39).

Aug 01, 2011 | KitchenAid K45SS Classic Stand Mixer

1 Answer

One of my blades is stuck and I can't engage the release


Make sure your Beater can slip in and out of the Beater Shaft
easily. Do not force the beater onto the Shaft if the shaft is bent.
If it cannot be removed easily by hand, use a soft rubber mallet
(not a steel hammer) to slightly tap the beater so it can be moved
up and down the shaft or from side to side. Then you can easily
turn the beater left and remove it from the shaft.

From Kitchenaid Manual:
To Attach Flat Beater, Wire Whip, or Dough Hook
1. Turn speed control to OFF.
2. Unplug stand mixer or disconnect power.
3. Tilt motor head back.
4. Slip beater onto beater shaft and press upward
as far as possible.
5. Turn beater to right, hooking beater over pin on shaft.
6. Plug into a grounded 3 prong outlet.

To Remove Flat Beater, Wire Whip or Dough Hook
1. Turn speed control to OFF.
2. Unplug stand mixer or disconnect power.
3. Tilt motor head back.
4. Press beater upward as far as possible and turn left.
5. Pull beater from beater shaft

Jul 19, 2011 | KitchenAid KSM150PS Artisan Series Stand...

1 Answer

First time using bread dough beater It was hard to put on and am unable to remove


Make sure your Beater can slip in and out of the Beater Shaft

easily. Do not force the beater onto the Shaft if the shaft is bent.

If it cannot be removed easily by hand, use a soft rubber mallet

(not a steel hammer) to slightly tap the beater so it can be moved

up and down the shaft or from side to side. Then you can easily

turn the beater left and remove it from the shaft.


From Kitchenaid Manual:

To Attach Flat Beater, Wire Whip, or Dough Hook

1. Turn speed control to OFF.

2. Unplug stand mixer or disconnect power.

3. Tilt motor head back.

4. Slip beater onto beater shaft and press upward

as far as possible.

5. Turn beater to right, hooking beater over pin on shaft.

6. Plug into a grounded 3 prong outlet.

To Remove Flat Beater, Wire Whip or Dough Hook

1. Turn speed control to OFF.

2. Unplug stand mixer or disconnect power.

3. Tilt motor head back.

4. Press beater upward as far as possible and turn left.
5. Pull beater from beater shaft.

Jul 17, 2011 | KitchenAid KSM90 Ultra Power Series Stand...

1 Answer

Bread dough beater will not come off


Make sure your Beater can slip in and out of the Beater Shaft
easily. Do not force the beater onto the Shaft if the shaft is bent.
If it cannot be removed easily by hand, use a soft rubber mallet
(not a steel hammer) to slightly tap the beater so it can be moved
up and down the shaft or from side to side. Then you can easily
turn the beater left and remove it from the shaft.

From Kitchenaid Manual:
To Attach Flat Beater, Wire Whip, or Dough Hook
1. Turn speed control to OFF.
2. Unplug stand mixer or disconnect power.
3. Tilt motor head back.
4. Slip beater onto beater shaft and press upward
as far as possible.
5. Turn beater to right, hooking beater over pin on shaft.
6. Plug into a grounded 3 prong outlet.

To Remove Flat Beater, Wire Whip or Dough Hook
1. Turn speed control to OFF.
2. Unplug stand mixer or disconnect power.
3. Tilt motor head back.
4. Press beater upward as far as possible and turn left.
5. Pull beater from beater shaft

Jul 17, 2011 | KitchenAid KSM90 Ultra Power Series Stand...

1 Answer

Hi, the speed lever won't move. I have checked that the bowl is securely placed and adjusted the height of the beaters? Can you tell me what else might be the problem. I have only had the appliance...


The Speed Control lever is linked to the Speed Link mechanism, which in turn moves the
Speed Control Assembly to allow the motor to operate at different speeds.
Get a Repair Part List from Kitchenaid.com for your particular model to see how it works.
As you select different speed setting, the Speed Link simply moves forward or backward,
thus pushing the Speed Control Assembly back and forth.
If you cannot move the Speed Control lever, means that the Speed Link is somehow bent
or out of place. Remove the Motor Housing and the End Cover and check it out.

Jul 01, 2011 | KitchenAid Artisan KSM150PSSM Stand Mixer

2 Answers

KitchenAid Professional 5 Plus - Runs at Full Speed


Hi. All of you have the same problem. The electronic speed control board needs to be replaced. This board can be installed without much trouble. The board is modular, remove the old board and install the new one. The wiring is connected by a modular plug.

Goto www.kitchenaid.com enter your model # and search for the parts manual. These drawings will assist you with the task at hand.

If this solution has assisted you, please rate it. Good luck! ricardok45

Jul 14, 2008 | KitchenAid KSM5PS Heavy Duty Stand Mixer

Not finding what you are looking for?
KitchenAid K45SS Classic Stand Mixer Logo

374 people viewed this question

Ask a Question

Usually answered in minutes!

Top KitchenAid Food Mixers Experts

Appliance engineer

Level 2 Expert

97 Answers

CJ C
CJ C

Level 2 Expert

66 Answers

Steve Allison
Steve Allison

Level 3 Expert

5569 Answers

Are you a KitchenAid Food Mixer Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...