Question about Yamaha RX-V1700 Receiver

Open Question

What does 'sur. decode' on the display screen mean of the yamaha rx-v671 receiver?

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

robotek
  • 1512 Answers

SOURCE: Input selector on my Yamaha RX-V596 stuck

Hi Dush

Sounds like the processor has locked up in the unit. Try powering it right down from the wall socket for a day to reset, and then retry operation. If that does not work, leave it disconnected for about 10 days to erase backup memory completely and then try again. Good luck. Don't forget to give me a "FixYa" rating if this works. If it doesn't, get back to me in here and we can talk more about it.

regards
Graeme

Posted on Feb 16, 2008

  • 1 Answer

SOURCE: Yamaha Rx-V870

I replaced it with a 6V lamp. Radio Shack part# 272-1140. It cost $1.49.

Posted on Feb 03, 2009

aparsons89
  • 40 Answers

SOURCE: problem with yamaha rx-c2092

Hi, try to unplug this unit from the wall for a minute or so, It may just need reset. If it still does this I would say that you have a loose wire inside where the power supply is. I would not recommend working on this unless you are computer savvy.

Posted on May 13, 2009

dunnbiker
  • 8546 Answers

SOURCE: Hi, have Yamaha RX-V467 receiver

Register and download the manual for free at retrevo.com

http://www.retrevo.com/s/Yamaha-RX-V467-Receivers-review-manual/id/23658bh533/t/1-2/

1) How is it with FM? That -35dB may be normal for this receiver. My old Pioneer is exactly like yours, inaudible at -50, whisper-quiet at -35 on all sources. But it will still crush my skull if I want it to.

2) Page 72. Press STRAIGHT to toggle out of Straight decoding mode.

Posted on Apr 24, 2011

  • 1170 Answers

SOURCE: Yamaha rx-v2600 displaying message "start upgrader

It shows "start upgrade" it means the upscaling videos to HDMI screen. ( High Bandwith Digital Multimedia Interface ).
It also scales component to 720p dvd quality...
Sound quality also increases..
So for that you need to upgrade it with proper functions .. For that you can call the shop people to do properly.

Thanks..

Posted on May 22, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

CMK-P3X for yamaha reciver RX-V670


  1. I have a yamaha receiver rx-v670.But it's one of part is damage which we not identified.we found a number on part body.VP832 and XK593 CMK-P3K.Please any one inform me the part name.Thanks.

Oct 27, 2012 | Yamaha RX-V671 7.1 Home Theater Receiver...

1 Answer

How to connect Niles #SSVC-6 Speaker Selector to Yamaha RX-V671


Greg, It pretty basic hookup,Just hook it up to your speaker terminal on the reciever or amp.To the input of the (Speaker) Selector.

Oct 04, 2012 | Yamaha RX-V671

1 Answer

Yamaha RX-V671receiver does not power on,


you should open the reciver, let it dry and with a thoothbrush clean the circuits.

it could help, but if anyrthing electric is burn inside you need to change it.

Sep 11, 2012 | Yamaha RX-V671

1 Answer

How do I reset my yamaha rx-v671 receiver?


If there is no apparent cause for the protection mode activating (such as shorted speakers, burning smell, blown fuses, lighting strike or mains power surges), reset the protection as follows and see what happens.

Connect power cord to mains and wait 5 seconds or so. While holding down "info" and "tone control" buttons, press "main zone" power button briefly and release, but keep "info" and "tone control" buttons pressed for at least 3 more seconds. The unit should power up. Assuming the reason for the protection has passed or been fixed, the unit can now be turned off and then back on with the "main zone" power button to restore normal operation mode.
If the protector activates again, the fault is still present and the unit needs to be repaired, ideally by a Yamaha authorised repairer.
There are dangerous voltages present in high power amps and a lot of grunt in terms of stored energy - best left to trained technicians.

Apr 20, 2012 | Yamaha RX-V671 7.1 Channel AV Receiver

1 Answer

Hi, have Yamaha RX-V467 receiver hooked up as follows: directv sat to Yamaha receiver via HDMI. blu-ray to receiver via HDMI. Receiver to Sony lcd tv via HDMI out to TV. Have 2 problems when watching TV...


Register and download the manual for free at retrevo.com

http://www.retrevo.com/s/Yamaha-RX-V467-Receivers-review-manual/id/23658bh533/t/1-2/

1) How is it with FM? That -35dB may be normal for this receiver. My old Pioneer is exactly like yours, inaudible at -50, whisper-quiet at -35 on all sources. But it will still crush my skull if I want it to.

2) Page 72. Press STRAIGHT to toggle out of Straight decoding mode.

Apr 24, 2011 | Yamaha RXV467 Receiver

1 Answer

My surround sound speakers don't work. No power


LCD will display which speakers are active. And this depends on 2 things: the source signal and decoder mode.
If source signal is stereo, only front L+R speakers are used. For 5.1 signal (for example DVD over HDMI / optical/coax spdif) all speakers installed (which are not set to None) are used.
To listen to stereo input signal using all speakers, switch decoder to enhancer mode.

Feb 24, 2010 | Yamaha RX-V457 Receiver

1 Answer

Hi i have a yamaha rx-v995 reciver and just percase new pioneer dv-320 dvd. it's output connection is with coaxial conector.when i connect the coaxial to the coaxial onector of my yamaha reciver i dond get...


1) Check to see if the screen says "EXT DECODER". If it does, press the EXT DECODER button again and this should fix the problem
2) Press input mode button until the display reads auto or digital. It may be set to analog.

Nov 16, 2009 | Yamaha RX-V995 Receiver

Not finding what you are looking for?
Yamaha RX-V1700 Receiver Logo

Related Topics:

103 people viewed this question

Ask a Question

Usually answered in minutes!

Top Yamaha Audio Players & Recorders Experts

 Grubhead
Grubhead

Level 3 Expert

5047 Answers

The Knight
The Knight

Level 3 Expert

74106 Answers

Electro Med Services...
Electro Med Services...

Level 3 Expert

6694 Answers

Are you a Yamaha Audio Player and Recorder Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...