Question about Barbeques Galore Grilling

Open Question

5 burner cap'n cook won't stay lit - Barbeques Galore Grilling

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 2 Answers

SOURCE: burner will not stay lit

Presuming the flame is touching the thermocouple, try putting slightly more pressure on the knob and hold for a few seconds longer. If this doesn't work try going through the same process with the knob removed - if this works you need to put a small piece of packing in the shaft of the knob ( a small piece paper might do). If this fails you need a new thermocouple.

Posted on Nov 18, 2007

Ad
vitg55
  • 73 Answers

SOURCE: Burner not lighting

Yes, you need a technician. It could be spark module or spark igniters on each burner.

Posted on Dec 15, 2008

hiltonjug
  • 612 Answers

SOURCE: imperial gas fryer problem, when the burners are

You have a bad gas valve. It's not reading the signal from the thermostat. The gas valve is stuck open.

Posted on Oct 19, 2009

localwonder
  • 6784 Answers

SOURCE: all cook top burners spark when any is turned on

OK, the best action is to call for service, if the unit was just installed, and purchased. This unit should be covered at this time, by the manufactures warranty, or store 30 day warranty. This repair should be free. The culprit will be a faulty spark ignition switch, and module. Testing is required. Once this switch, or(module), is replaced, the unit will operate correctly.

Posted on Nov 04, 2009

blueextc3221
  • 15935 Answers

SOURCE: When lighting one of the burners, the ingnition knob has to be held down over ten seconds for the flame to stay lit when the knob is released..

Thanks for your question!

I'm sorry that you haven't received an answer yet.

The response rate on FixYa FREE questions is usually over 80%, but sometimes questions go un-answered when:
1. the question is unclear, incomplete, or poorly worded...
2. the question is mis-categorized - so the correct experts aren't viewing it...
3. the question requires an answer for something that cannot be explained online adequately...
4. specific training, tools, or equipment are required to avoid injury or death...
5. the Experts that are online simply don't have the resources to answer your question fully...

Please feel free to re-work your question if you feel one of these may be the reason.
Of course you are not required - but converting your question to a PAID one usually increases the reply rate as well.

Normal rates for FixYa are...
$ 9.99 answer for one question.
$12.99 Live Real-Time online chat or premium e-mail support.
$29.99 Live Real Time phone support
Sometimes FixYa will run specials for unlimited questions via monthly subscription or reduced rates for limited periods.


Consider the savings that can be had when an informed Expert can save you a $100 service call, or a $350 trip to the car dealership.
Your problem solved - guaranteed! Or your money back!!

If you don't want to pay - feel free to re-submit your question so it returns back to the top of the work queue if you still need help.

Thanks for using FixYa - a 4 THUMBS rating is appreciated for helping with your FREE question

Posted on Sep 05, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I changed the thermo coupler and the pilot light does stay lit but the burners won't light


If you are referring to a gas fireplace:

  • Make sure the pilot knob is turned from "pilot" to "ON" or it will never run.
  • If the pilot knob is "ON", and the pilot is lit, but the burner won't light, it could be a bad Thermopile. The thermopile is the other safety mechanism in the pilot assembly that controls the burner.

Dec 19, 2012 | Heating & Cooling

1 Answer

JGBP90 gas range - precise simmer burner won't stay lit


Check the "Orifice Spud" to be sure that it doesn't have a partial blockage.

Nov 30, 2012 | Kitchen Ranges

1 Answer

Pilot light won't stay on


What is the model number of the unit?

Nov 27, 2012 | Tappan Kitchen Ranges

1 Answer

Malta dryer burner won't stay lit


usually a clogged vent or I've seem a coil go bad that allows it to light once but not the second time in the cycle

Feb 01, 2012 | Maytag Dryers

1 Answer

Have a home depot ducane 5 burner. just replaced burner tubes. have never used the rotisserie burner on it before. it lights but won't stay lite after releasing knob...any suggestions? Thanks


Infrared burners requite that the gas control knob be held in for 2 minutes or so, to allow the thermocouple on the infrared burner to heat up completely. If it's windy were you are, the wind can blow the burner out, while trying to light it. That's why it has a thermocouple on it, to stop the gas if the burner goes out. All cooking on the rotisserie is doon with the lid/hood closed, at temperatures around 250 degrees F. Once the infrared burner turns bright red, release the control knob.

Hope this helped you to get it lit. Thanks for choosing FixYa.

Aug 24, 2011 | Ducane 30400040 Stainless Steel Grill

1 Answer

The burners light, but it takes an inordinate time for them to stay lit. One of the burners will not stay lit when the knob is released, regardless of how long you depress the knob.


Need a new fsd ( looks like a small brass pencil) for the burner that won't light. The alignment of the ignition electrodes needs looking at and there over all condition I. E broken , worn , misaligned ect

Jul 13, 2011 | Bosch PGL985UC 36 in. Gas Cooktop

1 Answer

I have a stainless steel Ducane BBQ with five burners plus side burner and a rottisserie burner , which does not work. It is approx 5 years old and I have never used the rottisserie till last week. I have...


Since you've never used it. It may simply be a case that the infrared rotisserie burner is dirty and clogged with grease from cooking on the main burners. In addition, the Thermocouple and the igniter for that burner may also have a grease build up. In which case it won't allow the burner to light.

The electronic igniter that lights the main burners, also ignites the the rotisserie burner. Are you geting the click noise on the main burner igniters? If not, the battery in the igniter button needs to be replaced. Be sure to take note of the way the old battery is facing, when you unscrew the igniter cap. Because, that's the way the new battery should face.

Also, try match lighting the rotisserie burner. To do this, turn the Rotisserie Burner's Control Knob to the ON position and push it in, as you touch the lit match to the burner. If the burner lights continue to hold the burner knob in for a couple of minutes. This allows the Thermocouple and the ceramic plaques to heat up completely. Then slowly release the burner knob and the burner should remain lit.

If it doesn't stay lit, clean the burner and the Thermocouple ,in the manner that is described in your Owner's Manual.

Hope this helps you troubleshoot and solve the problem. Please let me know and Happy Grilling!!

Jun 15, 2011 | Ducane 30400040 Stainless Steel Grill

1 Answer

Jenn-Air SVD48600B grill burners have gotten weaker over time (seems like low flow of gas) and not the back will stay lit and cook but the front flicker on and off but not stay lit on its own. What is the...


do you have any carbon built up in the holes of the burners if so these would need to be cleaned every single small hole on the burner needs to be able to have a clear opening for the gas to travel out of? Message me back if the burners are cleaned and there is no carbon build up on the under side in this case you may have to make an adjustment to your gas valve Thanks again Rick

Jan 09, 2011 | Jenn-Air Kitchen Ranges

1 Answer

Kenmore wall oven keeps showing error codes f5 and f3. Unit will not say on.


oven went into E2 F3 oven code while cooking a chicken and broil burner came on turned off oven but broil burner stayed lit, then had to unplug

Nov 13, 2009 | Kenmore 47702 / 47704 / 47709 Electric...

1 Answer

Burner not lighting


Yes, you need a technician. It could be spark module or spark igniters on each burner.

Dec 15, 2008 | Cooktops

Not finding what you are looking for?
Grilling Logo

Related Topics:

47 people viewed this question

Ask a Question

Usually answered in minutes!

Top Barbeques Galore Grilling Experts

Paul Carew

Level 3 Expert

2557 Answers

Gary Kenady
Gary Kenady

Level 2 Expert

140 Answers

Dan Webster
Dan Webster

Level 3 Expert

8220 Answers

Are you a Barbeques Galore Grilling Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...