Question about Washing Machines

1 Answer

Hotpoint aqualtis washing machine model AQXXL 129 PM my doors not locking stopping in a cycle ,and water not draining , and lights flashing

My doors not locking stopping in a cycle ,and water not draining , and lights flashing

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 25 Answers

Find a dealer and get a manual for the washer it will have a trouble shooting section will tell exactly what is wrong

Posted on May 17, 2014

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Hotpoint aqualtis AQXXL 129PI


could be a bad timer? sticking at the wash cycle. it does agitate right? other wise bad water pressure switch

Aug 07, 2014 | Hotpoint Washing Machines

1 Answer

Hotpoint aqualtis washing machine model AQXXL 129 PM , runs through the cycle then stops at times leaving water in the drum and all lights flash why ?


the pump could possibly be jammed. you will need to drain the machine and remove the filter to check for any obstruction

May 17, 2014 | Hotpoint Washing Machines

1 Answer

I have washing machine aqualtis aqgl 129 pm and the ligh start pause flask and the machine dont work


Have you selected a program? Is water available? You haven't selected delay?
Then I suspect it may be a faulty door sensor, it wont start if it thinks the door is not shut. Try opening and reshutting the door.

Jan 27, 2011 | Hotpoint Washing Machines

1 Answer

Light flashing halfway through cycle


Start with the basics. Do you have the right detergent and the right amount of detergent? It sounds to me like that could be it. Too many clothes or not enough clothes could do it too. These new washers weigh the load and make an attempt to fix problems by stopping. The motor over amps with suds problems. It has to run more cycles to get the water clear. Yeah the machine checks the water. So if you have too much soap or the wrong soap or the soap in the wrong portion of the dispenser that could be causing it and then their could be a clogged pump filter.



If you need further help, reach me via phone at https://www.6ya.com/expert/dan_73bbd84fe1d95b61

Apr 03, 2010 | Washing Machines

1 Answer

Hotpoint BWD 129 machine starts to fill -


Try on a cold wash or rince cycle, if this then works it could be faulty heater element.

Feb 12, 2010 | Washing Machines

2 Answers

My Hotpoint Aqualtis AQXXD 169 PM is adding time to the was cycle, taking longer to wash through the cycle? ant ideas?


the time is a generic time and will adjust accordingly as goes through programe-for example it allows a certain time to heat in the winter your cold supply may be colder so the machine needs longer to heat water-load size-if its adding more than 30 mins then check filter

Nov 11, 2009 | Washing Machines

3 Answers

Trouble shooting the hotpoint aqualtis aqxxf149pi flashing f08


my hotpint aqualtis aqxxf149pi make a funny grinding noise when it spins help please?

Jun 25, 2009 | Hotpoint Washing Machines

1 Answer

HOTPOINT WASHER DRYER WD440G


That means that the machine detected a problem at a certain point of the cycle and stopped.

If the machine stops when filling check the inlet valve and the water supply.

If it stops because ofervilling check the water level switch.

If it stops when the cycle is hot water only , then check the heating element.

If it stops when draining, then inspect drain filter, drain pump , and drain hose. You access the drain hose removing a panel at the front side of the machine.

If it stops when motor is supposed to spin faster (rinse) then it is motor control unit or motor coupler.

If it is none of the above, then it is a defective control board.


Feb 16, 2009 | Hotpoint Ariston WD440G Front Load...

1 Answer

Faulty washing machine


if its no heat there only 2 items it can be heater element or the thermostats u could test the element by replacing the plugged in wires with wires that hasve a plug on place the wires into right places turn the plug on and if the element works it will start to glow turn it off as soon as u see it glowing from the inside of the washer also u can check the thermostats by dropping them into hot water and u should hear them pop

Nov 18, 2008 | Washing Machines

Not finding what you are looking for?
Washing Machines Logo

Related Topics:

189 people viewed this question

Ask a Question

Usually answered in minutes!

Top Washing Machines Experts

Donald DCruz
Donald DCruz

Level 3 Expert

17130 Answers

yadayada
yadayada

Level 3 Expert

80637 Answers

Brad Brown

Level 3 Expert

17328 Answers

Are you a Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...