Question about KitchenAid KECD806R 30" Electric Cooktop, 4 Elements, Tri/Dual Ring Elements, Infinite Heat Control

1 Answer

How to replace an element

Center element of the triple hot plate is not working

Posted by on


1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that got 5 achievements.


    An expert who has answered 20 or more questions within one hour.


    An expert who has answered 20 questions.

  • Expert
  • 118 Answers

This could be a couple of issues, but unfortunately if it's your element, you would have to replace the entire element, not just the middle part. What's the rest of your model number? I can find a part number for you. (KECD806R****)

Posted on Jun 17, 2014


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Had hob for 18months no problems, now two hotplates wont work & today the child lock light is on & nothing else will work, nothing.

remove the child lock setting and the remainder will work
those hot plates that were not working may need new switches, thermostats or replacement elements
call an accredited appliance electrician to get it all working again

Jun 13, 2015 | Cooktops

1 Answer

2 Hot Plates won`t work

If it's a gas buner usually the pilot light tube is clogged. If it's electric either the switch or the electric element isdefective. Did they both go out at the same time?

Mar 12, 2015 | Cooktops

1 Answer

My neff helectric hob two of the plates are not working

Sounds like the heating elements burnt out.

Dec 12, 2011 | Cooktops

1 Answer

The double hot plate only works in the center ring, and cannot be turned off except from the wall

I note this cooktop came with a 2 year warranty.

All of the elements are controlled by item 16 of this manual:

You will have to click on your model number to see it and probably have to enlarge the view.

The part number is 532037 but crosses to 533023 on several websites and sources.

If your having to pull the wall plug to shut it off this is the most probable failure.

Expensive part but most likely what it will take to correct your problem.

Thanks for choosing FixYa.


Sep 10, 2010 | Fisher and Paykel CT560QX 23 in. Electric...

1 Answer

Triple Element does not burn on single mode.

I ordered a replacement part from Sears Direct and used their schematic for a guide.

Jan 14, 2010 | Kenmore Cooktops

1 Answer

Chef Supreme Co-ordinate Series Ser. No.: 2004434294 Manuf. No.: 091E11SE1 Sales No.: RETSZW Hot plate not working & suspect bad element or thermostat? 1. The element is not an exposed coil, but rather...

this could be a 220 v unit and one side of the lines is out . ck your power at the breaker and at the cook top . if power is ok I would think it's the control sw . and not the plate .. you will need a volt /ohm meter to test . whirl / g e / frigidair / have genric switches that should replace yours .. hope this will help mm

Dec 03, 2009 | Cooktops

3 Answers

Frigidaire ES340 Range One element from Dual element doesn't work

The elements DO BURN OUT. Replace it.

Often you can see evidence of a hot spot on the element where the final failure occured, but not always.

Oct 27, 2009 | Cooktops

1 Answer

Stove plates have three settings. High, med, low.

60 years old . quite possibly not worth fixing .

Mar 05, 2017 | GE Cooktops

1 Answer

Cooking element

If the grilling elements does not get hot enough, then the main reasons for that are:
Escessive air movement across the grill.
Surface controls may not be properly set.
and the voltage maybe low.
But if is not getting hot at all then you can check by exchainging the elements to see if it is the element itself, and if it is the element then you will need to replace it.
I hope this help!!
If you need to replace it I know a place that are very cheap for Jenn-Air parts and super fast delivery...Let me know.
Eddie rentas
Tupper Lake

Jul 13, 2008 | Jenn-Air JED7430 Electric Cooktop

Not finding what you are looking for?
KitchenAid KECD806R 30" Electric Cooktop, 4 Elements, Tri/Dual Ring Elements, Infinite Heat Control Logo

Related Topics:

148 people viewed this question

Ask a Question

Usually answered in minutes!

Top KitchenAid Cooktops Experts


Level 3 Expert

1211 Answers

Dale Copeland
Dale Copeland

Level 2 Expert

102 Answers


Level 2 Expert

44 Answers

Are you a KitchenAid Cooktop Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides