Question about Pramac Electrical Supplies

Open Question

PRAMAC GENERATOR ENGINE NOT WORKING UNDER LOAD

Posted by Anonymous on

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 474 Answers

SOURCE: need to change oil on my generator Pramac 16 hp

brigsandstratton.com

Posted on Oct 31, 2009

  • 1 Answer

SOURCE: portable generator head stopped making power

portable generator head stoped making power engine runs fine sircut brakers are fine

Posted on Mar 16, 2010

kel1guy2002
  • 3740 Answers

SOURCE: perkins 3 cylinder powered pramac generator

Start looking at your safety circuits.

1. High water temp
2. Low Oil
3. Low water etc...

From the manual these are the protection circuits.

• Engine protection: low oil pressure, high engine temperature.
• Genset protection: under/over voltage, overload, battery charger failure, battery voltage out of limits,
under/over frequency, start failure.
• Circuit breaker protection: IV poles.
• Differential protection.


Any one of them will trip the fuel relay closed. What you may be able to do is disconnect one at a time each protection circuit and see when the fuel relay opens. (Make sure to reconnect each one if it had no effect on the fuel solenoid)

Once you isolate which circuit it is in then you can chase wires or change the bad switch.

Thanks for choosing FixYa.

Kelly

Posted on Jun 26, 2010

  • 1702 Answers

SOURCE: pramac ES7000 genset

Hi, Something is wrong with the govener (stuck or bent). Look to see for obstruction when you crank the throttle. Or maybe a better spring on it.
Good luck

Posted on Feb 27, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My diesel pramac P9000 generator engine is not starting even cranked for long time what is the problem


Check and replace the spark plug, clean filters and try again. If this doesn't fix it, it is probably the carb. Clean it and try a SMALL squirt of starter fluid

May 14, 2014 | Pramac Electrical Supplies

1 Answer

Why my Pramac P9000 Generator does not start


Try a shot of starting fluid. If it does not start with that it may have a fuel supply problem.

May 14, 2014 | Pramac P6000s - 6000 Watt Portable...

1 Answer

My generator start the breaker trips under load and stops engine but with out load no trips


First check the load and grounding, you will need to measure the amperage draw wih an ammerter, also check to see if it trips when a large unit like a motor or air conditioner starts, it may not be able to handle the inrush. Also be aware that if your breaker is a 30amp does not mean you can pull 30amp you can safely constantly draw 80% of that. Also check your grounding of the equipment you are powering.

Dec 09, 2013 | Yanmar Diesel 5500 Watt Pramac Generator

1 Answer

How to change oil in pramac gsw 50kw towable generator?


If you have a Yanmar engine...
There is a hose that is connected to the oil pan in place of the drain plug directly under the oil filter that will have an end cap. This hose is used to drain the oil into a waste container.
Download the service manual located at the address below and follow the instructions in the manual.
http://www.martindiesel.com/Documents/New%20TNV%20DIRECT%20Service.pdf
Hope this helps.

Aug 21, 2013 | Pramac Electrical Supplies

1 Answer

Perkins 3 cylinder powered pramac generator


Start looking at your safety circuits.

1. High water temp
2. Low Oil
3. Low water etc...

From the manual these are the protection circuits.

• Engine protection: low oil pressure, high engine temperature.
• Genset protection: under/over voltage, overload, battery charger failure, battery voltage out of limits,
under/over frequency, start failure.
• Circuit breaker protection: IV poles.
• Differential protection.


Any one of them will trip the fuel relay closed. What you may be able to do is disconnect one at a time each protection circuit and see when the fuel relay opens. (Make sure to reconnect each one if it had no effect on the fuel solenoid)

Once you isolate which circuit it is in then you can chase wires or change the bad switch.

Thanks for choosing FixYa.

Kelly

May 24, 2010 | Pramac GBW30P Encl Diesel Genset w/Perkins...

2 Answers

Portable generator head stopped making power


portable generator head stoped making power engine runs fine sircut brakers are fine

Mar 16, 2010 | Pramac Electrical Supplies

Not finding what you are looking for?
Electrical Supplies Logo

Related Topics:

33 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pramac Electrical Supplies Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

RSole

Level 3 Expert

688 Answers

Dinesh Nagal

Level 1 Expert

20 Answers

Are you a Pramac Electrical Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...