Question about Kenmore 3.8 cu. ft. HE4t Front Load Washer

Open Question

Why is Kenmore he4t spinning slow? - Kenmore 3.8 cu. ft. HE4t Front Load Washer

Posted by Anonymous on

Ad

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: Kenmore HE4T won't stop on the Spin Cycle. Stays

Replaced the relays with the 16Amp rated ones from Digitel.

Posted on Aug 17, 2009

Ad
blueextc3221
  • 15935 Answers

SOURCE: Kenmore Elite HE4T Washer

This advice is for Kenmore Elite and Whirlpool Duet model front loading washers. If you experience a problem where the door becomes jammed and will not unlock or open, here's an easy way to gain access inside your washer WITHOUT calling the repairman.

1. Remove the lower panel under the door by loosening the three screws under the bottom edge on the front of the washer. HINT: If you prop up the front feet of the washer with some small blocks of wood, this will make access to the screws much easier.
2. With the screws removed, the lower panel should drop down then come off. If the panel sticks, a light tap on either side will knock it loose.
3. Reach your hand up inside the washer behind the front casing on the right-hand side. This is where the door latch assembly is located.
4. At the bottom of the door latch assembly is a small pull tab. This is the manual release for the door. Pull the tab straight down and the door will come open.

Sometimes these doors will not unlock for whatever reason. If there are no error codes being generated, this could have just been a momentary glitch. If you see "Fdl" "DLE" or "Fdu" error codes, these are usually indications of a failed door latch assembly and will require replacement.


Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question.

Posted on Sep 18, 2010

SOURCE: Kenmore Elite HE4t washer won't spin

What does the S2 code stand for on a he4t washer

Posted on Oct 07, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to repair HE4t with HF code?


HE4T had problem on control board when early time version. Later they modified control board and find new version should fix your problem.

Apr 24, 2014 | Kenmore 3.8 cu. ft. HE4t Front Load Washer

1 Answer

Kenmore he4t code hf


hf error stands for hot water not being detected, make sure both hot and cold water are open and not reversed. if unit overfilled and flooded garage, the is if with you pressure switch or pressure hose. remove to lid of machine and you will find pressure switch and hose to the right side, inspect hose for any pin holes, if ok, order pressure switch

Apr 03, 2013 | Kenmore 3.8 cu. ft. HE4t Front Load Washer

1 Answer

Self cleaning button sequence want start


you need to see in the bottom of your washer or take the back panel and some of this washers have a reset button, try due that, make sure is unpluged while you due this, clean all the contacts inside and check all the wires make sure they okay

Oct 17, 2012 | Kenmore 3.8 cu. ft. HE4t Front Load Washer

2 Answers

Stop frequently on spin and rinse cycle F6 code


I have a Kenmore Elite he4t front load washer that was working fine and then we moved and now it stops washing midstream and flashes an F and a H. I have to pause and restart then it will stop washing again after a few minutes and flash the same codes again. I reset again and then it stops with 1 minute left and will not drain.

Apr 06, 2010 | Kenmore Elite 45986 Front Load Washer

1 Answer

Kenmore HE4T won't stop on the Spin Cycle. Stays


Replaced the relays with the 16Amp rated ones from Digitel.

Aug 15, 2009 | Kenmore Elite 45986 Front Load Washer

3 Answers

Kenmore Elite HE4t washer won't spin


The motor controller board is likely bad.


Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question.

Jan 06, 2009 | Kenmore Elite 45986 Front Load Washer

1 Answer

F Code for the Kenmore Elite he4t Front Load Washer (3 years old)


Hi! ricksmith
What is the first three digits of the model number.
The he4t I have reference to does not have a "F" code error. Most of the codes are two digit, PF, F1 to F9 etc.
You could try: Pressing Pause/Cancel two times to clear code. As well as unplug for 20 seconds. Do you have power fluctuations in your area.
InMrFixIt

Aug 27, 2008 | Kenmore Elite HE4 Electric Dryer

1 Answer

HE4t King Size Washer Balance Problem


remove the lower acess panel ( 3 screws across bottom) check for broen suspension/shock absorbers

Mar 02, 2008 | Kenmore 3.8 cu. ft. HE4t Front Load Washer

Not finding what you are looking for?
Kenmore 3.8 cu. ft. HE4t Front Load Washer Logo

Related Topics:

23 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kenmore Washing Machines Experts

Sal DeAngelo

Level 3 Expert

2254 Answers

fordexpert

Level 3 Expert

5537 Answers

 Brian Main
Brian Main

Level 3 Expert

464 Answers

Are you a Kenmore Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...