Question about Televison & Video

1 Answer

What to do with red blinking ON/OFF button on philips mci500h 12

Hello, The ON/OFF button is blinking red. Impossible to switch on. Any ideas what it is and what to do? Thank you

Posted by on

  • 1 more comment 
  • Adeline
    Adeline May 15, 2014

    Just for specification: it is a hi-fi unit, called streamium

  • Adeline
    Adeline May 16, 2014

    Thank you very much for your help. I unplugged the unit over the night and pluged it again

  • Adeline
    Adeline May 16, 2014

    and plugged it again in the morning. What happened is that the speed of the flashing changed. It became so fast that the light nearly was a still red. So I tried to switch the unit on using the remote control. But unfortunately nothing happened. So I unplugged it again...

×

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Welcome Back:

    Visited the website for 2 consecutive days.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 11 Answers

Internal Power supply and could be a shorted diode or a relay could be causing the flashing red light. Usually the red light indicates the System is in stand-by mode or not in stand-by. If when you used to turn it off there was a red light though not flashing, then that means it is in stand-by so in that mode your remote works on some older sets work and others it doesn't matter because the remote will always work. Unplug it for a half hour and try it and see if the light stops flashing. Might help to give more clues towards the fix.

Posted on May 15, 2014

Testimonial: "Thank you very much for your kind help. I tried your suggestion but unfortunately I did not quite succeed."

  • Ralph Sabean
    Ralph Sabean May 16, 2014

    Obviously the fuse isn't blown but the High Voltage regulator might be at fault. The regulator usually puts out about 130 DC and this is pulsed to the Flyback transformer and then the fly back builds up the very high Voltage for the CRT. I'm in Annapolis Royal and I have a second hand Black Monitor that I believe works and would sell it for $20 dollars and will hook it up to my Desk top to make certain it works before selling it to you.

×

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Hello I have a panasonic plasma Mdel TC- P50S1 It blinks 12 times I can't find the code for it can anybody help me


Those blinks [flashes] are fault indication (Error Codes). From the number of blinks occur at one time switch ON, you can get an idea about the faulty circuit section inside it. This will make repair easy. These are called blinking codes. Make sure about the exact number of blinking of the standby/power LED, by switching On & OFF the set, for at least two times. Count it carefully. If you wish to get some details, check the site linked here. It has details about blinking codes, and fault locating procedure, to many popular brand TVs and other devices.
http://electro-medical.blogspot.com/
http://homenol.blogspot.com/
http://electronicshelponline.blogspot.com/
If blinks continue without any pause, the main board is faulty.
Search the site by type in the "brand name" to your device, in the "Search box at the top right of the display window of the Homepage" to get gathered related posts.
Counting of number of blinks to Philips TVs is entirely different to that of other brand TVs. It is not a direct count procedure. The site have details about how to count the number of LED blinks [Fault Codes] to Philips brand TVs are given; along with details of the faulty circuit location.

Jun 02, 2017 | Panasonic Televison & Video

1 Answer

How do I start a philips hepc 8512 pc - power button led flashes red every two seconds - doesn't start?


These blinks [flashes] are fault indication (Error Codes). From the number of blinks occur at one time switch ON, you can get an idea about the faulty circuit section inside it. This will make repair easy. These are called blinking codes. Make sure about the exact number of blinking of the standby/power LED, by switching On & OFF the set, for at least two times. Count it carefully. If you wish to get some details, check the site linked here. It has details about blinking codes, and fault locating procedure, to many popular brand TVs and other devices. http://electronicshelponline.blogspot.com/
Blinking codes details to many popular brand TVs are given. Surf the site with patience. If blinks continue without any pause, the main board is faulty.
Counting of number of blinks to Philips TVs is entirely different to that of other brand TVs. It is not a direct count procedure. The site have details about how to count the number of LED blinks [Fault Codes] to Philips brand TVs are given; along with details of the faulty circuit location.

Nov 11, 2014 | Televison & Video

1 Answer

How do I start a philips hepc 8512 pc - power button led flashes red every two seconds - doesn't start?


These blinks [flashes] are fault indication (Error Codes). From the number of blinks occur at one time switch ON, you can get an idea about the faulty circuit section inside it. This will make repair easy. These are called blinking codes. Make sure about the exact number of blinking of the standby/power LED, by switching On & OFF the set, for at least two times. Count it carefully. If you wish to get some details, check the site linked here. It has details about blinking codes, and fault locating procedure, to many popular brand TVs and other devices. http://electronicshelponline.blogspot.com/
Blinking codes details to many popular brand TVs are given. Surf the site with patience. If blinks continue without any pause, the main board is faulty.
Counting of number of blinks to Philips TVs is entirely different to that of other brand TVs. It is not a direct count procedure. The site have details about how to count the number of LED blinks [Fault Codes] to Philips brand TVs are given; along with details of the faulty circuit location.

Nov 11, 2014 | Televison & Video

1 Answer

Philips mci500h 12


These blinks [flashes] are fault indication (Error Codes). From the number of blinks occur at one time switch ON, you can get an idea about the faulty circuit section inside it. This will make repair easy. These are called blinking codes. Make sure about the exact number of blinking of the standby/power LED, by switching On & OFF the set, for at least two times. Count it carefully. If you wish to get some details, check the site linked here. It has details about blinking codes, and fault locating procedure, to many popular brand TVs and other devices. Viewing it in "Mosaic" or "Magazine" will make surf easy.
http://electronicshelponline.blogspot.com/
Blinking codes details to many popular brand TVs are given. Surf the site with patience. Do a search by type in the brand name of the device to the search box.
Counting of number of blinks to Philips TVs is entirely different to that of other brand TVs. It is not a direct count procedure. The site have details about how to count the number of LED blinks [Fault Codes] to Philips brand TVs are given; along with details of the faulty circuit location.

May 15, 2014 | Televison & Video

1 Answer

How to program a CL035A philips universal remote to a polaroid tv


Hello
To programme with TV do the following.

Direct Code Entry

1. Press and hold the CODE SEARCH

button until the red indicator stays

on, then release the CODE SEARCH

button.

2. Press and release the desired Mode

button (TV, VCR, etc.). The red

indicator blinks, then stays lit.

3. Enter the 4 digit code from the code

tables. Note: after a valid code entry,

the red indicator turns off. For an

invalid code, the red indicator

flashes.

4. With your device on, press

CHANNEL UP. If the device

responds, no further programming is

required. Note: If some buttons do

not operate your device, try one of
the other codes for your brand.
NB: Switch OFF and switch ON your TV, each time before trying an other code, with its front panel power control switch and wait for about 15 seconds each time. OK

Feb 16, 2011 | Philips Televison & Video

1 Answer

Need the code for a sanyo tv to use a philips universal remote


Hello
Universal remote code to be cheked with Philips CL034 model remote habset to Sanyo are;

0506 0311 0612 0002
0428 0802 0412 0619

Direct Code Entry

1. Press and hold the CODE SEARCH

button until the red indicator stays

on, then release the CODE SEARCH

button.

2. Press and release the desired Mode

button (TV, VCR, etc.). The red

indicator blinks, then stays lit.

3. Enter the 4 digit code from the code

tables. Note: after a valid code entry,

the red indicator turns off. For an

invalid code, the red indicator

flashes.

4. With your device on, press

CHANNEL UP. If the device

responds, no further programming is

required. Note: If some buttons do

not operate your device, try one of
the other codes for your brand.
NB: Switch OFF and switch ON your TV with its front panel power control switch each time before trying an other code.
OK.

Feb 16, 2011 | Philips Televison & Video

1 Answer

I have lost the manual for my Crest model Po5094-2 remote. I need the code for Philips model 29PT468A TV. Can you please help?


Hello

four digit remote codes for Philips are:-
0062 0204 0184 0208 0205 0206 0207 0004 0189 0183 0199 0200 0288 0456 0003 0008 0068 0075 0086 0087 0141
Four digit remote code for Magnavox are:-
PHILIPS-MAGNAVOX ..... 0062 0204 0207 0183 0226 0288

Three digit remote codes for Philips are:-
003/ 004/ 006/ 008/ 062/ 068/ 069/ 074/ 075/ 076/ 086/ 087/ 089/ 133/ 163/ 183/ 184/ 205/ 206/ 207/ 208/ 212/ 213

Three digit remote codes for Magnavox are:-

PHILIPS/MAGNAVOX Codes: 183/ 184/ 208/ 213

NB: Switch OFF and switch On the tv with its front panel power switch each time before gointg to an other code.


Direct Code Entry

  1. Press and hold the SETUP button until the red indicator stays on, then release the SETUP button.
  2. Press and release the desired Mode button (TV, VCR, etc.). The red indicator blinks, then stays lit.
  3. Enter the 4 digit code from the code tables. Note: after a valid code entry, the red indicator turns off. For an invalid code, the red indicator flashes.
  4. With your device on, press CHANNEL UP. If the device responds, no further programming is required. Note: If some buttons do not operate your device, try one of the other codes for your brand.
Ok

Jan 15, 2011 | Philips Universal PH301S Remote Control

1 Answer

I can't find the code I need to program my universal remote to my television.


Hello

Three digit universal remote code for philips are:-
003/ 004/ 006/ 008/ 062/ 068/ 069/ 074/ 075/ 076/ 086/ 087/ 089/ 133/ 163/ 183/ 184/ 205/ 206/ 207/ 208/ 212/ 213

Four digit universal remote codes for philips are:-
0062 0204 0184 0208 0205 0206 0207 0004 0189 0183 0199 0200 0288 0456 0003 0008 0068 0075 0086 0087 0141
Four digit universal remote code for Philips Magnavox are:-
0062 0204 0207 0183 0226 0288

Proceedings:
NB: Switch OFF and ON your TV with its FRONT PANEL POWER ON/OFF SWITCH each time before trying an other code.
Direct Code Entry
  1. Press and hold the SETUP button until the red indicator stays on, then release the SETUP button.
  2. Press and release the desired Mode button (TV, VCR, etc.). The red indicator blinks, then stays lit.
  3. Enter the 4 digit code from the code tables. Note: after a valid code entry, the red indicator turns off. For an invalid code, the red indicator flashes.
  4. With your device on, press CHANNEL UP. If the device responds, no further programming is required. Note: If some buttons do not operate your device, try one of the other codes for your brand.
OK.

Jan 14, 2011 | Philips 42PFL3603D/27 42 in. LCD TV

1 Answer

Remote code for the tv


Hello

One amoung this will be your TVs' code.

Three digit remote codes for Philips Magnavox are:-

002/ 009/ 109/ 118/ 209/ 309/ 402/ 408/ 502/ 508/ 510/ 807/ 914/ 917/ 020/ 422/ 919/ 922/ 183/ 184/ 208/ 213

Four digit remote code for Philips Magnavox are:-

0062 0204 0207 0183 0226 0288 0062 0004 0009 0456 0183 0226 0288 0008 0068 0075 0141

NB: Switch OFF and then switch ON your tv with its front panel power switch [NOT BY THE REMOTE CONTROL HANSET]; each time before trying an other code.

Proceedings:-

Direct Code Entry
  1. Press and hold the SETUP button until the red indicator stays on, then release the SETUP button.
  2. Press and release the desired Mode button (TV, VCR, etc.). The red indicator blinks, then stays lit.
  3. Enter the 4 digit code from the code tables. Note: after a valid code entry, the red indicator turns off. For an invalid code, the red indicator flashes.
  4. With your device on, press CHANNEL UP. If the device responds, no further programming is required. Note: If some buttons do not operate your device, try one of the other codes for your brand.
Code Search If after trying "Direct Code Entry" your device does not respond, or if your brand is not listed, try doing a search of the code library for your code by following these steps.
  1. Manually turn on the device (TV, VCR, etc.) to be controlled.
  2. Press and hold the SETUP button until the red indicator stays on, then release the SETUP button.
  3. Press and release the desired Mode button (TV, VCR, etc.). The red indicator blinks once, then stays on.
  4. Press the CHANNEL UP button repeatedly (up to 300 times) until the device to be controlled changes channel. The red indicator blinks, then stays lit.
  5. Press and release MUTE to install the code. The indicator light goes off.
Most users will want to store VCR codes under the VCR button, Cable codes under CBL, etc. If you want to store a VCR code under CBL, etc., first follow the procedure for Direct Code Entry and press CBL in step 2 of Direct Code Entry, then enter ANY VCR code in step 3 of Direct Code Entry. Then follow the steps above for Code Search
OK.

Dec 25, 2010 | Philips Magnavox 27MS343S 27" TV

1 Answer

Philips 50p8342 problem


I have tv proyection philips model 50p8342, it is blinking red color on the power switch botton four times and then pause then another four time continuosly.

Aug 15, 2008 | Philips 60P8341 60" Rear Projection...

Not finding what you are looking for?
Televison & Video Logo

Related Topics:

451 people viewed this question

Ask a Question

Usually answered in minutes!

Top Televison & Video Experts

The Knight
The Knight

Level 3 Expert

75283 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17130 Answers

Cindy Wells

Level 3 Expert

5380 Answers

Are you a Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...