Question about Epson RIP Station 5000 Series II (C850072HA) RIP station

1 Answer

I have an Epson RIP Station 5000 that I use with my Stylus 5000Pro printer. When i boot up the rip it goes through its usual start up and when it gets to the Window display that says "Fiery LX Idle" the green light keeps on flashing like it is busy. A few minutes later it will start the reboot process again and just keeps doing the same thing over and over.

Posted by on

  • l_matteson Jun 23, 2009

    I just tried solution1 even with just the power cable hooked to it, it still wants to keep resetting itself over and over.




    Larry

  • l_matteson Jun 24, 2009

    How do I reset the firmware I can not find any disks with the firmware on them can I download it somewhere?




    Larry

×

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 297 Answers

This must be a prboelm because of improper powering down of the system. Remove all the plugged up stuffs behind and switch it on just with power cable after keeping it idle for some time.

Posted on Jun 23, 2009

  • sabharish
    sabharish Jun 23, 2009

    Perform a total reset of the firmware. This is surely a software problem.

  • sabharish
    sabharish Jun 24, 2009

    The firmware will be available from Epson sutomer support. They dont have it in their website.

×

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why is Epson Pro 7880 printing double image while in bidirectional


That sounds like your wiper blade that cleans the drum between prints is showing some wear and not cleaning properly.
Running a cleaning cycle may help, but it is likely that wiper blade needs to be replaced. Hope It's resolve all Your Printer Problem,
Or Still having Problem Then follow Us For
Epson Printer Support

May 16, 2014 | Epson Stylus Pro 7880 InkJet Printer

1 Answer

We are having problems printing a 10' x 42" banner on our Epson 10000 plotter. We are using a Xante Symphony RIP networked to the Plotter. For some reason it stops printing at approx. 76% (3/4) of...


STEVE you have to print it as a tiled image. there is an update on the epson website for this issue. basicly anything over 90" you have to tile as two images split in half with no border in between if that makes sense. they explain it well in the update. when its something 120" x 36" lets say i run the set up at 36 x 60 then go to the page set up and there should be a box for tie image when you preview it again it shows the tiled image put back to back. you also have to tell it toreverse the print. i use adobe cs2 illustrator and it works well.

May 28, 2011 | Epson Stylus Pro 10000 InkJet Printer

1 Answer

The printer has fed in 20 sheets of paper and jammed how do we release it


you will have to pull softly to make sure it will not rip then put one page at a time

Jul 12, 2010 | Epson Stylus DX4450 All-In-One InkJet...

2 Answers

Need manual and adjustment programme for epson 11880


My Epson Stylus Pro 11880 color ink-jet printer work fine but my problem is they can't print more than 7ft long & suddenly it's stop printing.

Jan 16, 2010 | Epson Stylus Pro 11880 InkJet Plotter...

3 Answers

Waste Ink Pad Saturated


Will have to go in for service, no one sells the waste ink cartridges or pads. Had this problem with a HP printer i had. HP said i need to send it in and they swapped out the full part and sent back cost something like 20$.

Jun 23, 2009 | Epson Stylus Multifunction Inkjet Printer/...

1 Answer

Epson Stylus Pro 9880 Does Not Print


Normal 0 Driver could be corrupt.
Disconnect the printer or at least be sure it is turned off. I'd do both and reinstall the CD software program that came with the printer. When the software program asks you to connect the printer to the USB port, do so and it should again work properly.
Hope this helps. Bud

Jan 08, 2009 | Epson Stylus Pro 9800 InkJet Printer

1 Answer

Printer Lexmark T630


The error message is normally caused by either plugging accessories into the rip controller board or the engine board. In some models the board may be conbined. Or invalid or illegal commands sent from the printer. Try upgrading the firmware first. If that does not work you you may have a bad board. Hope this helps Click on the link below and select your operating system http://downloads.lexmark.com/cgi-perl/downloads.cgi?ccs=229:1:0:359:0:0

Sep 10, 2007 | Epson Stylus Photo 1280 InkJet Printer

Not finding what you are looking for?
Epson RIP Station 5000 Series II (C850072HA) RIP station Logo

Related Topics:

58 people viewed this question

Ask a Question

Usually answered in minutes!

Top Epson Computers & Internet Experts

teamtech
teamtech

Level 2 Expert

74 Answers

kakima

Level 3 Expert

102366 Answers

Les Dickinson
Les Dickinson

Level 3 Expert

18394 Answers

Are you an Epson Computer and Internet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...