Question about Pyle Car Audio & Video

1 Answer

Reset pyle PLDNV695

NOT RESET

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 790 Answers

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Cannot open pyle astro with pattern unlock feature. cannot remember pattern. want to reset.


You must do a factory hard reset to overcome this problem of a lost/forgotten pattern.

Mar 24, 2017 | Pyle Cell Phones

1 Answer

Pyle PLDNV695 radio. How do I install it?


You need an interface module so it will work with the vehicle ! The radio is hooked up to the class 2 serial data bus , if you don't hook it up right the vehicle will not start an run !

Feb 24, 2015 | 2002 Chevrolet TrailBlazer

1 Answer

How to reset your pyle Astor


If there is no reset button behind the faceplate (usually small and either black or sometimes red ) Press it and hold it down with the tip of an ink pin for at least ten seconds , when you release it it should have reset your unit. If you don't see the reset button , just disconnect the power wire (red) and 12 volt constant power (yellow) for about 10 seconds as well. That should do it ! Good luck !

Feb 01, 2015 | Pyle Car Audio & Video

1 Answer

I have a Pyle PLDNV695 radio that when you shut it off for more than 10 seconds, you have to reset the radio and reprogram the radio stations. What could the problem be ???


Double check the yellow wire, making sure it always has battery voltage on it where it connects to the radio. If it does, there is an internal problem in the radio.

Dec 22, 2014 | 2005 GMC Sierra

1 Answer

Pyle troubleshooting


Buy a cheap USB memory and stick it in the terminal to make it shut up.

Aug 19, 2014 | Pyle Pldnv695 6.95 Double-Din In-Dash...

1 Answer

How to reset a Pyle PTC157LC remote?


To do a hard reset, just unplug the TV from AC mains wall socket, and re-plug it back after 15 minutes or so. This procedure will make it a hard reset. If you want to make it a system reset [Factory Reset]; you have to enter its service mode option, and select the factory reset option. If you wish to get some details; check the site linked here. Pull up older posts. Surf the site with patience. http://electronicshelponline.blogspot.com/
Service mode entry, adjust and exit procedure to many popular brand TVs are given. Never forget to exit the service mode, after all adjustments have been done.

Aug 15, 2014 | PyleHome Pyle PTC157LC 15.6 Hi-Definition...

1 Answer

When i turn on the car the radio doesnt go to the home page it goes to a screen with circle and arrows number 1234


You have the unit wired wrong. When you shut your key off the radio loses ALL power and it needs ACC power to maintain the memory. If not, the unit will reset itself. The screen you see is the touchscreen calibration screen. Just follow the " X " around the screen to 5. Then the unit will boot up again. You will have to reset radio stations and EQ and speaker settings. If you don't fix the ACC wire, you will have to do this A LOT!

Dec 06, 2013 | PYLE Audio PYLE PLDNV695 6.95 DOUBLE-DIN...

1 Answer

Im looking for the reset button on my pyle chopper series pla2200 amplifier...i was requested to look on the back of the amp or by the 'plug in fuse' near the input sockets and i still cant find it, what...


Dude, there is no breaker button, there are two 15amp fuses on the speaker connect end of the unit. Here is the link to Pyle: http://www.pyleaudio.com/manuals/PLA2200-2210-2220-4200.pdf
If it's not a blown fuse then you will need service.

Jul 05, 2009 | Pyle PLA2200 Car Audio Amplifier

2 Answers

Car multi cd changer wont eject


hi
do you have any model numbers on the cd changer?

Nov 23, 2008 | Car Audio & Video

Not finding what you are looking for?
Car Audio & Video Logo

Related Topics:

240 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pyle Car Audio & Video Experts

xxxxxx xxx

Level 3 Expert

4834 Answers

The Knight
The Knight

Level 3 Expert

73594 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7689 Answers

Are you a Pyle Car Audio and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...