Question about Onkyo TX-SR605 Receiver

4 Answers

Onkyo tx-sr605 no sound?

Can`t get any sound no matter which inputs connected (selected). Tried factory reset, change cables but still no luck. Checked most of parts inside, like output transistors, diodes but can`t find any faulty ones. Any help or lead appreciate. Thanks

Posted by on

4 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Passionate:

    Visited the website for 10 consecutive days.

    Habit-Forming:

    Visited the website for 3 consecutive days.

  • Expert
  • 64 Answers

It's often a problem with some of the 256 soldering legs underneath the Digital Sound Processor (DSP). Need to be fixed at a service center.

Posted on Aug 17, 2016

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Master
  • 1,342 Answers

Does this unit have a headphone jack?

What is your speaker setup? What cable are you using to connect?

Posted on May 16, 2014

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    New Friend:

    An expert that has 1 follower.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 87 Answers

Check the speakers ohm. Check the protection relaies if they are clicking.

Posted on May 15, 2014

  • Level 1:

    An expert who has achieved level 1.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 6 Answers

Are you connected by HDMI? If so, your HDMI board may be faulty. I was having major drop outs with picture and sound until I got it replaced.

Posted on May 14, 2014

  • 1 more comment 
  • kestas666 May 14, 2014

    as per description not getting sound no matter which input used, optical, analog or hdmi... Video works without any issued

  • thej762000 May 14, 2014

    Have you ran the test tone? Any response from the speakers at all?

  • kestas666 May 14, 2014

    as per two previous answers ---> no sound

×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Onkyo tx-sr605 no sound


you need a new digital board (really expensive). There is a chip on these board (Q3001) that goes bad and doesn't allow part of the firmware to load. This causes the unit to not have any audio output.

May 12, 2014 | Audio Players & Recorders

1 Answer

Unable to connect a blu ray dvd player to onkyo tx-sr605 via hdmi


Not sure what unable to connect means..but I will assume you have the correct cable.

First make sure you have plugged the from the HDMI cable from the DVD play into the IN 1 HDMI port on the back of your Onkyo

On the Receiver
Enter the Setup mode
Select INPUT OUTPUT ASSIGN
Next make sure the HDMI monitor out is set to YES on the Receiver
Monitor out
HDMI Monitor - YES

Next you need to assign the HDMI INPUT to DVD
Select INPUT OUTPUT ASSIGN
HDMI INPUT
DVD - IN1
CBL/SAT - IN2

This may be your issue.

Next step would be to verify your television input settings.

Nice receiver!

Best of luck!

Apr 13, 2011 | Onkyo TX-SR605 Home Theater Receiver 7.1...

1 Answer

Onkyo sr605: needs to "warm up" before video


check your display section, is there any problem?

Jan 08, 2011 | Onkyo TX-SR605 Receiver

1 Answer

Sound won't play through Onkyo TX-SR605 when using HDMI


The chances are that you have selected an incorrect sound setting or not switched it on, for the HDMI you are using. With Onkyo receivers each connection will have it own settings for video and sound. You just need to look in the manual as to how to select the settings.

May 08, 2017 | Onkyo TX-SR605 Receiver

1 Answer

I have an Onkyo TX-SR605 AV receiver that just stopped outputing video to my Panasonic projector. I have connected other devices directly to the projector and video is fine, so the problem is not the...


Goof information. Have you eliminated or proven the Onkyo as a cause by going direct to the projector? Try another Input and/or Output. It's best to know which component is broken and if it's limited to a specific subset of its function.

Settings are also indicated. Run through the video setup again. If it just stopped, what preceded it?

Nov 27, 2009 | Onkyo TX-SR605 Receiver

1 Answer

Onkyo605 stopped outputting Video after installing HDAV1.3 sound


If you didnt change any of the inputs going to the onkyo. I would check the input setup. I dont know what input you have your pc connected to on the onkyo, i'm guessing that your using a hdmi cable. make sure you have hdmi selected as your input type not component video or any other. That model doesnt upconvert anything to hdmi. Also some dvi-d to hdmi dont play well wih onkyo.

Aug 16, 2009 | Onkyo TX-SR605 Receiver

1 Answer

DVD signal received in wrong aspect


PRESS SETUP GO TO MISCELLANEOUS PRESS ENTER THEN DOWN TO OSD SETUP PRESS ENTER AGAIN AND DOWN TO MONITOR AND CHANGE TO 16.9.

HOPE THIS HELPS.

CABLE GUY.

Feb 21, 2008 | Onkyo TX-SR605 Receiver

1 Answer

Onkyo 605 HDMI Sound


Change the setup in the Hardware control/HDMI/ HDMI Audio...

Jan 17, 2008 | Onkyo TX-SR605 Receiver

1 Answer

Onkyo TX-SR605 conected to Mitsubishi DLP TV


What I think I did and how I fixed it!

FACTORY RESET ON EVERYTHING!



All you have to do is to do a factory reset on everything, but I thing mostly on your 605, but I would do it on the TV as well. I think what had happened is after I set everything up for the first time, it worked great. As the days when on I started to play with all of the futures the 605 and the TV had to offer. I was turning them on and off to see what everything did. What I think I did was, I turned on something in the 605 that the TV did not know how to cope with. If I had to guess, I think it is the Lip-sink feature (Spelling?) in the 605.

Anyway disconnect everything, look in your manuals of the TV and the 605 to see how to do the factory reset on both. Then turn your TV on. After it does it’s start up for the first time (again), start connecting the 605.

It has been working great for me after I did this. Do not count on help from the people you bought it from or the people who made it. This stuff is so new they do not really know how to fix it.



Robert…

Jan 04, 2008 | Onkyo TX-SR605 Receiver

1 Answer

Cable connection to Onkyo TX-SR605 7.1


You will have to connect your coax to the tv coax input.You can view cable this way.To use the hdmi input to tv,you will have to change your input settings back and forth on the tv menu from hdmi to rf input.There is no way to hook your cable to the txsr.

Oct 22, 2007 | Onkyo TX-SR604 Receiver

Not finding what you are looking for?
Onkyo TX-SR605 Receiver Logo

171 people viewed this question

Ask a Question

Usually answered in minutes!

Top Onkyo Audio Players & Recorders Experts

 Grubhead
Grubhead

Level 3 Expert

5056 Answers

The Knight
The Knight

Level 3 Expert

74136 Answers

Electro Med Services...
Electro Med Services...

Level 3 Expert

6694 Answers

Are you an Onkyo Audio Player and Recorder Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...