Question about Golds Gym StrideTrainer 380 Elliptical

1 Answer

Where can I get a replacement belt for my ellypitcal ?

Hello , anyone there?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 2,509 Answers

Yes there is someone there and thank you for asking.
Is there a reason you are unable to do a simple search?
Do you expect an immediate answer? If so sorry you had to wait.
I'm afraid I will have to guess what part of the world you live in as you don't say.
Parts for use with Gold Gym Equipment

Posted on May 13, 2014

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Hello,my treadmill belt jerking without stepping on it,when I increase the speed it gets shut off,can anyone guide me,what could be the problem?


Try to adjust the belt tension. also try lubricating the running belt. Even after that the problem persist the you have to check the carbon brush of the motor or the motor need to be replaced,
To know more about treadmill belt tension and lubricating check the link.
http://electro-medical.blogspot.com/

May 13, 2016 | Exercise & Fitness

2 Answers

How do I replace the smaller belt that attaches to the brush


Hello! Follow the steps below to replace the v-belt on your Hoover.

1. Slide flat belt off large pulley.
2. To remove v-belt, slide back of belt over pulley. Then firmly pull on belt and snap it off. Discard used belt.
3. To install new belt (with lettering on outside of belt) slide back of belt over pulley and pull front of belt toward groove next to pulley. Belt will pop into place.
4. Insert brush-roll through belt and position belt in groove on brush-roll.

I have also included a link you may visit to view the owner's manual and these instructions.

http://hoover.com/file/509/

Jun 30, 2014 | Hoover U6476-910 WindTunnel Upright Vacuum...

1 Answer

Slipping belt


Hello!
The belt on your Magnesium is a fiber reenforsed belt that is designed to not stretch from normal use. Therefore it is not the easiest to acesss when it does need replaced. The belt will need replaced likely. The beltis on the left side of the vacuum and requires you to remove the side of the unit as well as to make it easier the bottom blue piece that is over the brushroller. Honestly I would advise anyone with this issue to take it to an Oreck repair center. Because ethe belts don't stretch it's difficult to roll the new belt on. Hope this helps!

Jan 28, 2013 | Oreck Magnesium Upright Vacuum Cleaner

1 Answer

Broken tensioner pulley 2002 tundra


Serp belts and tensioners should always be replaced as a pair, by the time the belt is shot the tensioner is to, just a fact of life. Thats why many parts places sell them together as a kit. You shouldnt have to be tearing any further into the engine to replace the tensioner, they are generally a quick bolt on replacement for 99% of the vehicles out there.

May 04, 2017 | Cars & Trucks

1 Answer

I have a 2002 1500 silverado 2wd. 4.8 liter vortec. When I have my Ac the belt squils like crazy. The only time it doesn't is when I'm sitting. But I kno it's a tension problem cause I see the...


Hello Danny, when you replace a tensioner you normally replace the belt as well, i would check the ac unit clutch assy for faults for there might be faulty bearings at the clutch assy there should be no play or warble in this assy, check with the belt removed, to check belt tension you should be only able to twist the belt about and no more than half a turn with you hand at the location of the largest span between pulleys with the belt installed

May 16, 2012 | 1999 Chevrolet K1500

1 Answer

DOES ANYONE HAVE THE BELT DIAGRAM FOR A 200 FORD FOCUS THE BELT BROKE AND i COULD NOT FIGURE HOW THE NEW ONE GOES ON


Hello. look around inside of the engine compartment, on the inside of the hood, and in your owner manual. They always put a diagram of the serpentine belt somewhere.

Dec 05, 2009 | 1995 Ford Taurus

2 Answers

Need a diagram for 94 3l diesel hilux timing belt replacment pls.


Hello Paul
I hope this help you
6a737ed.jpg Regards Paul
www.limotec.co.uk
If you need more please contact me

Jan 13, 2009 | 1994 Toyota 4Runner

1 Answer

Changing the belt on a GE front loading washer


Hello , i can try to help , I have always got these belts on by starting the belt on the small pulley/motor , then rolling it on the large pulley , kinda like putting a bike chain on. Let me know if you have any other questions and how it turns out.

Phil

Jan 07, 2009 | GE WSXH208A Front Load Washer

Not finding what you are looking for?
Golds Gym StrideTrainer 380 Elliptical Logo

Related Topics:

74 people viewed this question

Ask a Question

Usually answered in minutes!

Top Golds Gym Exercise & Fitness Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Steven's...
Steven's...

Level 3 Expert

426 Answers

Sock Puppet

Level 3 Expert

246 Answers

Are you a Golds Gym Exercise and Fitnes Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...