Question about E-Machines eMachines Desktop PC

1 Answer

Desk top not working properly

Desk top takes 3 to 4 min. to come on after being in standby.
It works fine afer it does come on....???? wrong

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 5 Answers

Disable the standby and just use a screen saver instead.

Posted on Jun 23, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Wont stay on. It'll load for 3 secs then turn off


The Calculator has a feature that takes it into standby after a certain delay of inactivity. Possible values of the delay are 1 min, 3 min, 5 min, 10 min, and 30 min.
In view of this, your 3 sec value seems too short. I suspect that the batteries are depleted.

In OS 2.x, press 5: Settings & status, then 3:Handheld Setup. Look for drop down box to the right of Power Standby, and select a longer delay.

Feb 04, 2011 | Texas Instruments TI-Nspire Graphic...

1 Answer

Monitor is properly connected to desktop computer. When Ipress button to power up the lite on the monitor goes from a green to a yellow color. The monitor does not work. WHAT AM I DOING WRONG?


From what you are saying, it sounds like the monitor is not getting the video signal from your PC, it goes into standby mode if it does not receive the signal from PC.
Does it do the same with another PC? It may have internal problem but we need to find ou first if it is the PC or the monitor problem.
Is it PC desk top or laptop?

http://www.fixya.com/support/r5093881-lcd_flat_panel_tv_troubleshooting_guide
http://www.fixya.com/support/r6150077-basic_lcd_monitors_troubleshooting
Failed TV and Monitors: http://s807.photobucket.com/albums/yy352/budm
Learn about bad caps: http://en.wikipedia.org/wiki/Capacitor_plague

Dec 06, 2010 | Emprex LM2201 22" LCD Monitor

1 Answer

GHW9100LW1 F-11 code right afer it starts


Hi


Thanks for using FixYa. F11 is a communication error between the central control unit (CCU) and the motor control unit (MCU). To start with check the wire harness connections between CCU and MCU, and then check the motor. If both of them appear to be working fine then it seems that the MCU of your washer has gone bad as the control unit seems to be working fine. Please do rate the solution if the issue is resolved or post a comment for further assistance.


Thanks
Rylee

Jul 12, 2010 | Whirlpool Duet GHW9150P Front Load Washer

1 Answer

My internet in not working some lan probs


I have an emachine t5026 that won't turn on. It sounds like a car tying to start and the lights on the front flash as does the light on the mouse, but it won't start

May 08, 2010 | Gigabyte GA-945GCMX-S2 Motherboard

1 Answer

Yellow light flashing dodge caravan1998 reset afer 30 min rear wiper defrost ac


The blinking lights in the rear wiper rear defrost area can be reset by holding 2 buttons of the 3 on the left hand side. The top and bottom buttons. Turn the key on and hold them for about 10 sec and they should start flashing differently. Just let it do this. After they start flashing different. It will take 5 to 10 mins. Then one or more will quit flashing all together. If they don't after about 20 min reset them again it can take about 5 trys sometimes before they all go out. Good Luck

Nov 13, 2009 | 1998 Dodge Caravan

1 Answer

Desk top not along bottom properly icons all bunched up in a corner


right click on the start bar and make sure the 'Lock the Taskbar' option is not ticked (click on it if it is) . Afer that just drag the bar that aperars near the icons to the right:).

Oct 27, 2009 | Acer Aspire 5500 5570-2609 Laptop

1 Answer

My external hard disc worked well until today. Now the external light continues to flicker quickly and the hard disc does not show up on my desk top. I have a mac running Mac OS X 10.5.7. The serial...


Hi,

There is some thing wrong with file system on your hard disk drive.
Just unplugg it and wait for 1 min, Plugin again.

1) Go to Application -> Utility -> Disk Utility

2) You can see all the drives connected to the machine.

3) Select the drive from left side which acts as external and click on Repair disk button.

Sep 18, 2009 | LaCie Computers & Internet

1 Answer

Power goes off


Try resetting the unit.
Make sure there is no disc in the unit. With the unit on, go to the front panel and look for the STOP (square) button.
Hold it down until the unit shuts off by itself. Turn it back on it shoudl work fine.

Jul 01, 2009 | Samsung HT-X40 System

Not finding what you are looking for?
E-Machines eMachines Desktop PC Logo

Related Topics:

52 people viewed this question

Ask a Question

Usually answered in minutes!

Top E-Machines Computers & Internet Experts

Matthew Spark
Matthew Spark

Level 3 Expert

1066 Answers

Doctor PC
Doctor PC

Level 3 Expert

7733 Answers

Les Dickinson
Les Dickinson

Level 3 Expert

18394 Answers

Are you an E-Machines Computer and Internet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...