Waste Ink Pad Saturated

The Epson Artisan 835 waste pad is located in the printer's waste ink compartment and is designed to absorb any excess ink that is generated during the printing process. Over time, the waste pad can become saturated with ink, which can cause issues with the printer's performance.
To clean or replace the waste pad on an Epson Artisan 835 printer, you will need to follow these steps:

1. Turn off the printer and unplug it from the power source.
2. Open the printer's cover and locate the waste ink compartment.
3. Carefully remove the waste pad from the compartment.
4. Clean the waste pad with a damp cloth, or replace it with a new one if it is heavily saturated with ink.
5. Reinstall the waste pad into the waste ink compartment.
6. Close the printer cover and plug the printer back in.

It's important to note that this process can be messy and you should use gloves and old clothes to avoid getting ink on your hands or clothes. Also, some printer models may have a different process to access the waste pad, you might need to consult the printer's manual or Epson website to know more about your specific model.

Hello,

First thing to do is to disassembling the printer and replace the waste ink pad. After that you need to reset the waste ink counter, in this way the printer know the wasteink pad was replaced.To reset the counter you need to enter in service mode. To do this you need the service manual.



Cheers !

Get the User Guide from the Epson site for your printer. If that doesn't tell you what to do go back to the site and ask the question.

Waste ink pad typically captures ink waste when the printer cleans itself (print head). Resetting the counter without replacing the absorbent material can cause ink leakage and a profound mess.Epson suggests servicing the printer, but it may be more cost effective to replace it.

This refers to the internal counter, actually located in the software on the computer determing that your waste ink pads are likely saturated and need replacement. You can download software from either Epson at http://www.epson.com/cgi-bin/Store/support/InkPadsForm.jsp or at http://www.ssclg.com/download/sscserve.exe. Both of these software packages will allow resetting the counter. However one should either take the printer in to an authorized Epson or independent printer service company or if comfortable with messing around inside computers and peripherals, one can check the waste ink pad(s). On the RX700 there is a small access panel, on the back of the unit, on the left hand side when facing the back of the RX700. It is held in place with a Phillips head screw and small plastic latch tab on its bottom side. The pad material is clearly visible from here, with a pair of clear plastic waste ink tubes directed down into this waste ink receptacle. If this is saturated, wet and discolored, it should be replaced, before resetting the counter. Not doing so risks the excess waste ink overflowing and making a mess and possibly even shorting out some of the circuitry.

You need to reset your printer. Goolgle search for "indoreset for rx595" and download it. That is the program you need to use to reset the waste ink pad counter back to zero.

waste ink pad absorber is like a waste tank made of absorbent pads, in here the waste ink is absorbed. In time this waste ink pad will be saturated or full. When it happens the printer will suddenly stop working. The printer needs to be reset to function again and the waste ink pad replaced to prevent flooding of waste ink inside the printer. The waste ink pad is replaced by disassembling the printer.

You can also try dabbing the waste pad with absorbing paper. This worked for me.

Ink means pad for waste ink nearly full. Epson program read and count all waste ink from head cleaning and ink charge. Next, you need reset waste ink counter, and replace or washing pad. You can extend outlet pipe to outside of printer, so next time you don't need replace pad again.

First, we need to know what model # it is. A lot of the epson printers have a sponge in the bottom of the printer that the waste ink goes into. The waste ink comes from cleaning the heads. Everytime you turn on an Epson printer, it runs a head cleaning so your best bet with epson printers is to leave them on. You can get waste ink containers for most model on several ink supply websites, but you have to reset the waste ink notification before it will print again. There are several ways of doing this with the different printers, but you can download a program to help you. You can download it from here:

http://www.ssclg.com/epsone.shtml