Question about Lathem Time Office Equipment & Supplies

1 Answer

Lathemtime clock 2121 series

How to change the time?

Posted by on


1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

This site doesn't have much in the way of Lathem clocks or support. Go to for assistance.

Posted on Mar 26, 2008


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Changing the clock/internal time

The clock settings should be set to Auto so that the clock is set by the broadcasted signal; this will automatically update when the clocks change.

Note that Recording start and end times should be set to On Time to ensure that the broadcaster's start and end signals are used. If either of these are changed, the timing becomes manual, and functions such as Series Record are not available.

Mar 06, 2014 | Humax PVR9300T HD DVR

1 Answer

Fridgidaire stove clock not keeping correct time

Clock logic can not be changed replace the whole board
just lets you change the time will not let you slow it or speed up

Nov 14, 2013 | Frigidaire FGGF3054KF Gallery Series...

1 Answer

How do i program my clock in my 2002 land rover discovery

If If you mean the time clock, just keep pushing the little indentations below the clock with a pin to change the hour and then the minutes :-) If you mean the speedo clock, no can do, reads mileage from ECU and gearbox to prevent tampering with mileage.

Nov 07, 2011 | 2002 Land Rover Discovery Series II

1 Answer

How to set the clock on a 2429

Follow the instructions on page 5 of the manual at

Mar 01, 2011 | Vtech Cordless Phone Battery for 2429,...

1 Answer

How to set the time on a simplex series c model number 6334-9140 digital clock

For independent operation, the clock is connected to a reliable source of 120 VAC 60HZ (or 230 VAC 50HZ), and time is maintained with a real time clock chip. Switches located on the front of the clock allow for easy and accurate time setting. For system clock applications, synchronization can be accomplished by connection to Simplex BCD digital data for instantaneous time updates. Clocks can also be connected to power line carrier/synchronous timing inputs that provide hourly and 12 hour corrections. Impulse correction from the 6400 Series Master Clock is ideally suited for Time and Attendance System expansions. A capacitor in each clock maintains timekeeping for approximately 12 hours in the event of power failure in the facility. The Celestra 2000 can be corrected with six different clock codes to suit any specific retrofit or new synchronized time system.

Jan 30, 2011 | Office Equipment & Supplies

1 Answer

I have intermatic timer T30003R. How do I change the timer motor

My understanding is this timer uses typical T100 series 120Volt clock motor.
The motor has identifying numbers printed on it.
T100 series 120V clock motor is available at Grainger:
Selection of Intermatic clock motors are available on-line:

To replace motor:
Timer mechanism snaps out of box using a thumb-spring located at top of mechanism.
Clock is located on back of mechanism, and is held by 2 star-screws.
You can buy star screwdriver bit at auto parts store or hardware.
Clock motor has two white wires that are connected to terminals on front of timer.
Be sure to tighten terminals screws very tight after replacing clock motor.

Jan 10, 2011 | Intermatic & Indoor/Outdoor Rain Tight...

3 Answers

How do I set the clock

Set the clock by following these steps: a). Touch TIME pad. b). Turn rotary knob clockwise until CLOCK appears. c). Touch TIME pad. d). Turn rotary knob in either direction. The time displayed will change in 10-minute increments and indicate AM or PM. Turn the knob in the opposite direction and the display will change in one-minute increments. e). Touch TIME pad. The clock is now set. in some units there is button instead of knob in that case the clock indicating button has to be pressed . This will help. Thanks please keep updated.please do rate the solution positively .thank you for using fixya

Feb 06, 2010 | Bosch Appliances 27 in. Wall Oven Electric...

1 Answer



put your keys in so that your instrument clsuter on the dash come on,(no need to start the engine), use your mileage reset button to change time by turning it clockwise and anticlockwise till you reach the correct time.. it will change on your dash aswell as your radio..

Jan 05, 2009 | 2005 BMW 3 Series

Not finding what you are looking for?
Office Equipment & Supplies Logo

Related Topics:

180 people viewed this question

Ask a Question

Usually answered in minutes!

Top Lathem Time Office Equipment & Supplies Experts


Level 3 Expert

102366 Answers


Level 3 Expert

2237 Answers


Level 3 Expert

77932 Answers

Are you a Lathem Time Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides