Question about Black & Decker MX55 PowerPro Hand Mixer

1 Answer

How do you place beaters in mixer without them falling out?

I have tried unsuccessfully to place beaters in mixer but they will not stay in, it would be so much easier if it came with an instruction manual, can you help me?

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Novelist:

    An expert who has written 50 answers of more than 400 characters.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

  • Expert
  • 126 Answers

I can't find a manual for the MX55 online, Suzanne, but looking at the picture of it I found on Amazon and based on the manuals for other B&D models, it looks like you should have two slightly different beaters: one with a collar and one without and it's very important that each beater go into the correct hole. The one with the collar should go into the left hole (looking at the bottom with the holes at the top) and the one without a collar into the right. The other manuals say "insert each beater and, if necessary, turn it slightly until it locks into place." I hope this helps. Good luck!

Posted on May 12, 2014

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

The beaters will not stay up in my Oster stand mixmaster. The eject lever will not lock them in. Can it be fixed? Or could it be that I need new beaters because they are worn out and do not fit in


wild guess turn beater as you push in to allow the beater to engage the drive, a little like gears meshing. You should be able to feel it lock into the drive.

Dec 21, 2014 | Oster Food Mixers

1 Answer

Beaters will not stay up in my Oster stand mixmaster. The eject lever will not lock them in. Can it be fixed? Or could it be that I need new beaters because they are worn out and don't fit


They need to be replaced or the locking mechanism does, but in the meantime, wind some thread around the beater end and this may keep them in temporarily.

Dec 21, 2014 | Oster Food Mixers

1 Answer

How do I keep beaters in mixer without them falling out?


Each beater may be shaped differently and only will click into its appointed port. There may be a picture on the mixer showing which side to put each beater.

May 12, 2014 | Black & Decker MX55 PowerPro Hand Mixer

1 Answer

Gear cap which attaches to the drive spindle falls off


there should be a lip on the shaft that hold this up. You insert the shaft from the bottom and a pin goes through the gear to hold it in place. Look at the IPB HERE.

May 25, 2008 | KitchenAid KP2671 Professional 6 Series...

1 Answer

Sunbeam 2484 Beaters won't stay engaged.


In taking apart my same beater, I'm trying to figure out the alignment of the spring which provides the tension so that the beaters won't fall out. I'd assume that your spring has mis-aligned. You need to take it apart (3 Philips screws), and carefully pull the assembly apart. I'll bet your spring falls out like mine did. I'm trying to find a schematic from Sunbeam to see how the spring should align.

Nov 19, 2007 | Sunbeam 200 Watts 2484 Hand Mixer

2 Answers

Beaters fall down


Hi,

You have to change the planet hub and the beater.

Nov 06, 2007 | Kenwood KM800 Major Classic Stand Mixer

2 Answers

KitchenAid Hand Mixer Beater won't stay in slot


You need a new gear set.  Hard to find however.

Jan 07, 2007 | KitchenAid KHM3 Classic Hand Mixer

1 Answer

Sunbeam hand mixer. One beater not working


That spring does not turn the beaters. It is part of the beater release assembly. Probably one of the gears is worn.

Nov 12, 2006 | Sunbeam 2485 MixMaster Series Hand Mixer

Not finding what you are looking for?
Black & Decker MX55 PowerPro Hand Mixer Logo

148 people viewed this question

Ask a Question

Usually answered in minutes!

Top Black & Decker Food Mixers Experts

Jerry Greenberg
Jerry Greenberg

Level 3 Expert

1667 Answers

Karl Kittsteiner

Level 2 Expert

210 Answers

David Alger

Level 1 Expert

14 Answers

Are you a Black & Decker Food Mixer Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...