Question about Kenmore 3.8 cu. ft. HE4t Front Load Washer

Open Question

Kenmore he4t stopping loud vibrating sound

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 32 Answers

SOURCE: Kenmore two way tumble action washing machine - shakes, vibrates very loud

sounds like you have a broken stantion on the back of the basket.you can confirm this by opening the door and trying to pull up on the stainless steel basket.if it pushes up and flops back down,that is what you have.if the mach is over 2yrs old,look in your manual under warranty.if it has a 10yr on stainless steel basket and lifetime on tub,you will only have to pay for labor on repair.if it only has 1yr on entire mach,est would be higher than the price of a new one.

Posted on Sep 28, 2008

  • 1 Answer

SOURCE: Kenmore he4t washer

I had the same problem. The "fire alarm" sound is coming from the silver panel behind your washer. The panel is vibrating loudly during the wash cycle. A Sears repairman solved this by taking a small piece of cardboard (cut from a box) and wedging it between the side edge of the panel. He operated the washer's cycle and adjusted the tightness of the wedge until the loud sound stopped. It did! Hope this helps you!

Posted on Nov 02, 2008

jsrock516
  • 5911 Answers

SOURCE: HE4t Washer

"F06" is a Motor Speed error. The following link explains how to troubleshoot and some common causes:

http://www.fixya.com/support/r714929-f06_error_whirlpool_duet_kenmore_elite

The first step to troublehsooting should be to unplug the washer for AT LEAST 30 minutes in an attempt to reset the Central Control Unit (CCU). Sometimes this is all that it takes to correct momentary glitches with the unit. If the error code reappears following a computer reset, follow the advice given in the link I provided.

If you have questions, or require additional assistanc, please let me know. I hope this helps you.

Posted on Jan 23, 2009

  • 1 Answer

SOURCE: Kenmore HE4T won't stop on the Spin Cycle. Stays

Replaced the relays with the 16Amp rated ones from Digitel.

Posted on Aug 17, 2009

blueextc3221
  • 15935 Answers

SOURCE: vibration on second floor laundry

Check the Vibration damper rods to be sure that...
1. They are there and mount is solid.
2. If they are broken in 1/2.
3. The plastic knuckle mounts are not missing/broken.
4. There is oil in the shock absorber/spring section of the rods.

Also - there are suspension springs on the bottom of the tub that could be broken and/or missing.

Replace/repair as necessary.

IF THIS IS A BRAND NEW INSTALLATION - be sure you hav removed the basket shipping pins (4) that secure the tub during shipping.

Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question.

Posted on Sep 16, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Hi, I have a Kenmore quietquard dishwasher model number 587.14012406a and it's making a loud noise throughout the wash it then stops and then restarts which is a vibrating noise and is extremely loud!


suggestion, i suspect you have got something in the wash pump or the pump impeller is breaking up this can cause a vibrating noise or it could be the rince pump.

Nov 20, 2016 | Kenmore Dishwashers

1 Answer

Purchased microwave in 2005, just stopped heating and now its making a loud noise


if the loud noise is like a vibrating noise then it sounds like the high voltage diode.

Mar 23, 2010 | Kenmore 63252 Microwave Oven

2 Answers

Loud vibration


If it is a frost free check the fan inside. The fans can have bearing failure after a few years thus causing the vibration. Also the compressor underneath is mounted on rubber vibration dampers and if one of these rubber mounts fail then the compressor will start vibrating against the refrigerator frame causing a loud vibration. If none of these apply gently press on the side and front panel of the refrigerator to try and locate the source of the vibration as any where metal is vibrating against metal the side and front panel act as a sounding board amplifying the sound. If you cant locate the vibration then you may have a more serious problem and may need to call a technician.

Oct 09, 2009 | Roper Refrigerators

1 Answer

Kenmore HE4T won't stop on the Spin Cycle. Stays


Replaced the relays with the 16Amp rated ones from Digitel.

Aug 15, 2009 | Kenmore Elite 45986 Front Load Washer

1 Answer

Vibration on second floor laundry


Check the Vibration damper rods to be sure that...
1. They are there and mount is solid.
2. If they are broken in 1/2.
3. The plastic knuckle mounts are not missing/broken.
4. There is oil in the shock absorber/spring section of the rods.

Also - there are suspension springs on the bottom of the tub that could be broken and/or missing.

Replace/repair as necessary.

IF THIS IS A BRAND NEW INSTALLATION - be sure you hav removed the basket shipping pins (4) that secure the tub during shipping.

Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question.

Apr 06, 2009 | Kenmore 3.8 cu. ft. HE4t Front Load Washer

1 Answer

Kenmore he4t washer


I had the same problem. The "fire alarm" sound is coming from the silver panel behind your washer. The panel is vibrating loudly during the wash cycle. A Sears repairman solved this by taking a small piece of cardboard (cut from a box) and wedging it between the side edge of the panel. He operated the washer's cycle and adjusted the tightness of the wedge until the loud sound stopped. It did! Hope this helps you!

Jul 01, 2008 | Kenmore 3.8 cu. ft. HE4t Front Load Washer

1 Answer

Kenmore he4t washer


Sounds like you need a new water valve (some debris inside the valve causing it to not fully close). These are availible from your local appliance parts store or on line from the manufacture. Once you have your replacement, just take the #20 torx screws out of the top panel and remove it. Your valve should be on the back left hand side.

May 22, 2008 | Kenmore 3.8 cu. ft. HE4t Front Load Washer

1 Answer

Kenmore 3.8 cu. ft. HE4t King Size Capacity


remove feet set on stand and put the 4 screws in 2 in the front 2 in the back the remove the drawer and level the 4 legs on the stand then lock the lock nut if you git a little vibration raise the front washer up 1/8 in usely will take care of it

May 03, 2007 | Kenmore 3.8 cu. ft. HE4t Front Load Washer

Not finding what you are looking for?
Kenmore 3.8 cu. ft. HE4t Front Load Washer Logo

Related Topics:

13 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kenmore Washing Machines Experts

fordexpert

Level 3 Expert

5481 Answers

Mike Squire

Level 2 Expert

391 Answers

Robert Rankin

Level 2 Expert

338 Answers

Are you a Kenmore Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...