Zebra 110 pax 4

The Sonic Impact i-PAX device is an older portable audio player that may have been discontinued. If you have lost the USB remote and charger cord for the device, you may have trouble finding replacements. Here are a few options you could consider:

1. Check the manufacturer's website: Visit the Sonic Impact website or contact their support team to see if they still have the USB remote and charger cord available for purchase.
2. Search online marketplaces: Check online marketplaces such as Amazon, eBay, or Craigslist to see if you can find a used or refurbished set of the USB remote and charger cord.
3. Look for third-party options: Consider looking for third-party options such as generic USB remotes and charger cords that are compatible with your i-PAX device. However, be sure to check the specifications of the device to make sure that the replacement parts are compatible.
4. Check with electronics retailers: If you're unable to find the USB remote and charger cord online, try checking with local electronics retailers to see if they have any similar products that might be compatible with your i-PAX device.

I hope one of these options helps you find the replacements you need for your Sonic Impact i-PAX device!

Depending on the type of connection you are using it could be a Main board issue or Ethernet card failing. Make sure it is a printer issue and not a problem with cabling, IP addresses or your PC before replacing any parts. (ignore pictures FixYa is grabbing the wrong ones)

Main Board ZEBRA P1004273 MAIN LOGIC 8MB XI4 SERIES New

Ethernet card ZEBRA 79501 011 KIT INT PRINT SERVER 10 100 Refurbished

That error signifies a fuser problem where the thermistor does not detect the fuser coming to temperature. Need to replace fuser unit, part number 008R13022, see link.

http://www.iteminconline.com/008r13022_008r13022-xerox-workcentre-7132-fuser-110-volt.htm?source=froogle&gclid=Cj0KEQjw8u23BRCg6YnzmJmPqYgBEiQALf_XzZg4C5Qd7jYhL14rJSJWIPdkZdVrtP4kPg2RlOQFweIaAnzV8P8HAQ

There is a relay bank under the hood. According to TexasHonda
In the 03-06 models, a single relay provides pax, RR, LR window motor power. Relay is located in the pax Multiplex Control Unit in the pax side foot well. If you have power to the pax side window, relay is probably working.

Thank you for contacting FixYa with your printer inquiry.

The 50.3 is a fuser Temperature error. If your pages have toner and image but are smudging or smearing you know the fuser is not heating and needs to be replaced.

If your printer is still under warranty contact HP Customer Care for warranty replacement of fuser part numbers: RM1-1082 for 110 volt, RM1-1083 for 220 volt. (888) 999-4747.

If your printer is out of warranty, suggest you purchase a maintenance kit part # CB388A HP maintenance kit for LaserJet P4014 P4015 P4515, includes other needed high wear parts.

Excellent Illustrations:

http://www.printertechs.com/tech/mkinst/P4015/mk-p4015-2fuser.php

Maintenance Kit Contents:

Contents

1. What is included in a LaserJet P4014 P4015 P4515 maintenance kit?

2. Fuser installation.

3. Transfer roller installation.

4. Cassette feed/pickup rollers.

5. Tray 1 (manual feed) pickup rollers/feed rollers.

6. Reset the maintenance count.

Please rate this solution and post a comment if you need additional assistance.

There is no minimum lenght specified in the manual for this model. There are maximums however.

The manual can be obtained from here:

http://www.zebra.com/id/zebra/na/en/documentlibrary/manuals/en/printer_manuals/xiiiiplus_rxi_user_guide.File.tmp/13383L-004_RA_XiIIIPlus_UG.pdf?dvar1=ProductLiterature&dvar2=XiIIIPlus/R110Xi/R170Xi User Guide (en)&dvar3=46

Hope this helps,
Dan

Keeping up with the Drivers is a very good idea, it will fix little problems that come along from time to time. Try resetting the printer defaults by entering the menu system and exiting, at piont of exit don't save permanently but cycle around to load defaults and exit. Go back in and set the printer up again, this time exit saving permanently.

Did you design the label? Do you have any control over the label design? This is usually a sign that the printer is trying to excede the page limit (usually by one dot row) and is going to the next label to finish. By making the label length slightly smaller, you can stop this.

wow i love it, i place a post in the "forum" and hours later im asked to join a Preimum service for a fee, that im expected to feel good that for the feel my search can be solved............ oh but wait in the same breath im asked if i solved my own problem to post what i did to solve it............. for FREE,

yeah guess i came to the wrong web site, thanks but no thanks

This means Fuser failed to reach
standby temperature.
The only answer is to replace the fuser, part number 56P0648 110 VOLTS, 56P0671 220 VOLTS.
Please advise if you require instructions