Question about EnGenius EOC-3220 (EOC3220)

1 Answer

Ap mode i'm hearing the only way to access the ap once in that mode is through a serial cable. i've yet to be successful in that too though

Posted by on

×

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 481 Answers

Ignore the rumors. It's perfectly simply to converse with your APs through a browser. I do it daily. What may be throwing off your informant is that the default IP address of this unit changes from 192.168.1.1 to 192.168.1.2 when it is switched into AP mode, as documented in the accompanying manual. But a conscientious net admin isn't going to leave the units at their default addresses anyway.

Posted on Oct 28, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Whenever i download a video form the net it says unsupported codec


If you can't play videos once you've successfully installed the YouTube for Mobile app, one of the following issues may be causing the problem:

  • Your phone may not support streaming video. Check by trying to play a video at http://m.youtube.com
  • Your streaming video access point may need to be configured outside of YouTube for Mobile. Depending on your phone and mobile data provider, this access point may need to be the same or different from YouTube's. For more help with these settings, please see the "Access Settings" article.
  • If you've successfully played videos with YouTube for Mobile before, your network connection may not be strong enough at the moment. Please try again later.
  • Your carrier might block RTSP traffic which is required to transfer the video.

    hope this helps

Feb 29, 2012 | Samsung Corby 2 GT S3850

1 Answer

Recently formated my laptop via a usb flash drive since my cd/dvd rom doesnt seem to work,and unfortunately the cd/dvd rom still doesnt work,doesnt appear under my computer,i ve no way of accessing data on...


Hello
Head of to the Acer website.Put in your model and serial # of your laptop. Find and download the cd or dvd drivers and install them on your laptop.

Also have you done the windows updates? Usually this will solve the problem.

Mar 25, 2011 | Acer Computers & Internet

1 Answer

How do I set my linksys WRT300N router to infrastructure mode vs adhoc mode? I have a magnavox blu ray player with wireless capability, it says I have to set my wireless router to infrastructure mode vs ad...


http://compnetworking.about.com/cs/wirelessfaqs/f/adhocwireless.htm

http://compnetworking.about.com/cs/wireless/f/infrawireless.htm

Question: What is infrastructure mode in wireless networking? Answer: Infrastructure mode wireless networking bridges (joins) a wireless network to a wired Ethernet network. Infrastructure mode wireless also supports central connection points for WLAN clients. A wireless access point (AP) is required for infrastructure mode wireless networking. To join the WLAN, the AP and all wireless clients must be configured to use the same SSID. The AP is then cabled to the wired network to allow wireless clients access to, for example, Internet connections or printers. Additional APs can be added to the WLAN to increase the reach of the infrastructure and support any number of wireless clients. Compared to the alternative, ad-hoc wireless networks, infrastructure mode networks offer the advantage of scalability, centralized security management and improved reach. The disadvantage of infrastructure wireless networks is simply the additional cost to purchase AP hardware. Note that home wireless routers all feature a built-in AP to support infrastructure mode.

Feb 02, 2011 | Linksys WRT160N Wireless Router

1 Answer

Cannot connect my WAP-0005 Access point to my router


Use AP mode ; but may really have some compatiblity issues though... Good Luck*

Mar 11, 2010 | Levelone WAP-0005 (DHWAP0005) 802.11b/g...

1 Answer

Getting 169.254...


possibly cat5 cable problem or your DWL - 2100AP is only on wireless mode.

please check and put on mixed mode also.

Mar 08, 2010 | D-Link AirPlus Xtreme G DWL-2100AP...

1 Answer

Resetting my EOC-3220 via serial cable


The # will only appear if you monitor the EOC through the power-up sequence. If you are cabling into a running EOC, that # has already gone by. By that time, you no longer need to wait anyway, just type.
If you can't type in the text window, you may have HyperTerminal set up wrong, or may have the wrong brand or model serial cable. The EOC is pretty good about accepting input when it is supposed to.
However -- as long as you know what the current IP address of your unit is, you should be able to browse to it over the main ethernet cable and make whatever changes you need that way. The MAC address allow table isn't going to affect your local access in any fashion, it only controls who can connect wirelessly. This may be faster than trying to figure out how your serial connection is faulty.

Aug 12, 2009 | EnGenius EOC-3220 (EOC3220)

1 Answer

I have 2 3COM 3CRWE454G75 -> AP, it does work in AP repeater mode


find the ip address problem or the firewall of there or proxy servr is there and re-configure it then you get the it and check the region if not same that also creating problem sir,

Mar 04, 2009 | 3Com OfficeConnect (3CRWE454G75)...

1 Answer

I directly connected ap 5131 to pc but it is not pinging and cant login


1) Must be powered
2) Must use crossover cable
3) Connect to WAN port...

else, download the manual, get a serial cable, and connect to the console port using hyperterminal on 19200,8,none,1,no protocol...

Dec 13, 2008 | Motorola AP-5131 802.11a/b/g Wireless...

3 Answers

D-link dwl-2100ap in WDS mode Received Deauth: WLAN 1 11G STA


I have had similar problems with DWL-2100 and (much less often) with DWL-3200. I have no solution, but a workaround: changing the authentication mode. For example, if the units are using WPA-Personal, I change it (on both) to WPA2-Personal or WPA-Auto-Personal. It doesn't seem to matter which mode is used, it's just the fact of changing it that helps (eventually). You may have to go through the process more than once. Also, realize that although the web interface comes up 30 seconds or so after a reboot, it may take another 30-60 seconds before a link is established, so don't give up too soon while trying these changes.

Dec 03, 2008 | Computers & Internet

1 Answer

AP Mode Problems


Probably you have to learn that there are various people looking for an access of the internet through your facilities. Anyway, inorder to solve your problem these are the following recommendation I made just for you. Hope this will be helpful.

PHASE I
1.) How do I reset the EOC-3220 / EOC-3220 EXT / EOC-3220+ back to factory default settings? An RS-232 null modem serial cable is required for this procedure.
(where to buy it : http://www.keenansystems.com/store/catalog/product_info.php?cPath=3&products_id=221)

1. Connect the EOC-3220 to your computer with a null modem serial cable.

2. Start a HyperTerminal session: Click Start and then select Programs -> Accessories -> Communications -> HyperTerminal.

3. After the HyperTerminal window appears:
a. Give this new connection a name. Ex: EOC-3220.
b. Select correct COM port. Ex:COM1.
c. Set baud rate as "38400", data bits "8", parity "none", stop bits "1", and flow control as "None". Then press “OK” to bring up the HyperTerminal window.

4. Wait until the "#" is displayed in the HyperTerminal window.

5. Type "flash reset", then hit enter.

6. Type "reboot", then hit enter. After the device reboots, all settings will be at factory default.

Phase II

1.) Since that you already reseted the AP you need to use the default IP which is 192.168.1.1 user: admin password: admin

2.) Make it sure you need to use different IP such as 72.10.251.xxx and the subnet: 255.255.255.xxx

3.) The idea of configuration in come from your own desire which was no body can no longer try to match your network IP so that there will be no body access your AP anymore without your knowledge.

4.) You need to make you SSID invisible to everyone inorder no body no longer able to reach your SSID by setting up basic setting which is transparent to everyone.

5) And lastly change the default user and password of your AP.

Good Luck

Nov 24, 2007 | EnGenius EOC-3220 (EOC3220)

Not finding what you are looking for?
EnGenius EOC-3220 (EOC3220) Logo

Related Topics:

262 people viewed this question

Ask a Question

Usually answered in minutes!

Top EnGenius Computers & Internet Experts

Doctor PC
Doctor PC

Level 3 Expert

7733 Answers

Michael Vincent Cruz

Level 3 Expert

868 Answers

Karen Gibson

Level 1 Expert

16 Answers

Are you an EnGenius Computer and Internet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...