Question about Whirlpool Ultimate Care II LSQ9564J Top Load Washer

Open Question

Washer wi not spin

Drais and gitates but wont pin

Posted by Anonymous on

Ad

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
rylee_smith
  • 8619 Answers

SOURCE: washer wont drain

Hi

Thanks for using FixYa. Dishwasher not draining properly or not draining at all issues can arise due to different reasons. Usually, these issues are related to kinked hoses, knocked out disposer unit (if connected with the dishwasher drain hose) & clogged drain pump & filter.

Also note that dishwashers do not drain completely after a finished cycle and this is normal. Dishwashers are designed to leave some water in the unit to ensure that the heating element doesn’t overheat. If you suddenly begin to experience a large amount of water being retained in your dishwasher, you have a problem. Some of the most common reasons include that the drain hose isn’t working properly, the drain pump isn’t working correctly, or possibly there is a plumbing problem in your home’s drain lines.



First check whether the drain is not clogged or blocked and the line is not kinked. Check all the hoses for blockages & also clean the air gap. Has the disposer been replaced recently? If so, chances are the knockout is still in place. Simply remove the drain hose from the disposer, and knock out the plug. If the disposer has not been replaced, try removing the drain hose from the disposer and use a wet-dry vacuum (prepared for water, of course) to **** any water (and hopefully anything else) from the drain line. Then reconnect the hose, and test the unit. If you have checked the air gap and the drain hose and can’t locate the problem, then it is an issue with the drain pump of the dishwasher.

Please do accept the solution if the issue is resolved or else revert for further assistance.


Thanks

Rylee

Posted on Nov 22, 2009

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

The drum doesn't want to vibrate


If the washer won't agitate or spin, then the stator or rotor assemblies at the back of the washer tub might be bad or damaged. The rotor is essentially one half of a motor, it interacts with the tub by creating a strong electro-magnet. If the rotor fails or is damaged the washer might not spin or agitate. Check the rotor for damaged magnets or other defects

Oct 21, 2014 | LG WM-1832C Front Load Washer

1 Answer

Wy maytag bravos wont drai all


Check outlet filter is clear and hose aren't kinked

May 05, 2014 | Maytag Bravos MVWB400V Washer

1 Answer

Washer wont spin code e57


High current issue - 1. Remove the belt from the motor and spin the motor pulley. Does the motor spin free? No, replace the motor. Yes, go to step (3). 2. Spin the tub pulley. Does the tub spin free? No, check the tub bearings. Yes, go to step (3). 3. Disconnect the plug from the motor and measure the resistance of the windings (pin 1 to 2, pin 1 to 3, pin 2 to 3). All readings should be between 4 and 6 ohms. If readings are correct, replace the Speed Control Board. If readings are incorrect, replace the motor.

Aug 19, 2012 | Frigidaire Affinity ATF7000E Front Load...

1 Answer

The agitator isn't working at all


if this is the only problem solenoid on rocker arm there are 2 solenoids one for spin and one for gitator

Jun 12, 2011 | Washing Machines

1 Answer

Whirlpool washer wont spin out


put washer in spin cycle on close cover you should hear click if so check cutter pin on rocker solenoid no click wire to solenoid or solenoid or switch on cover door

Jun 10, 2011 | Washing Machines

1 Answer

Can some one help me??? My washer won't agitate


the model number would help me out in answering this question, feel free to call our free tech support and order parts from www.whirlpoolpartssurplus.com

Jun 23, 2009 | Whirlpool Washing Machines

1 Answer

Kenmore heavy duty washer wont spin but does everything else corr


you really still have a belt model? that unit is close to 30 years old now.
anyway if the unit looks like all is moving, then you may have a bad lid switch or most likely an open coil on the wig wag assembly.
it is the part the has 2 coils on a metal bracket on top of the transmission. it moves back and forth when the unit is running.
does it drain but just not spin? if so then you could just have a broken wire to the wig wag or the coil could be bad. wires do break to the wig wag , but you usually hear the coils engaging then shutting off if the wires are bad. so check the coils and try to replace the wig wag second if you dont find a bad wire.

Jan 31, 2009 | Kenmore 22422 Top Load Washer

Not finding what you are looking for?
Whirlpool Ultimate Care II LSQ9564J Top Load Washer Logo

Related Topics:

16 people viewed this question

Ask a Question

Usually answered in minutes!

Top Whirlpool Washing Machines Experts

Dan Webster
Dan Webster

Level 3 Expert

8220 Answers

Sal DeAngelo

Level 3 Expert

2295 Answers

yadayada
yadayada

Level 3 Expert

76691 Answers

Are you a Whirlpool Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...