Question about Homelite Consumer Products 9.0 Amp, 14 In. Chainsaw

Open Question

Where is the magneto on 2 stroke 330 homelite

Posted by Anonymous on

Ad

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: Homelite CSP 3314 Chainsaw

starts no prob will not rev , just stalls when you try

Posted on Feb 14, 2010

Ad
  • 4088 Answers

SOURCE: hi how to tune homelite 330 chain saw carby, idle

Before adjusting anything, check the fuel filter, air filter, and muffler for plugging. Check the condition of the fuel lines for decay or other damage. Tighten all carburetor fasteners. Make sure you have fresh fuel mix in the tank. Does the primer bulb pull fresh fuel into itself when pumped? Turn both jet screws CW to stops (lightly), then back out CCW 1-1/2 turns each. This is a basic setting and should allow the engine to start and run. Start the engine and allow it to warm up, then pull the throttle full on. Adjust H needle CW until the engine starts to speed up, but still 4-stroking. Proper final adjustment is when the engine 4-strokes unloaded, but immediately 2-strokes when cutting. Release the throttle and adjust L needle CW for fairly good idle, but still allows the engine to 'follow the throttle'. Adjust idle speed screw so that the chain stops turning, but the engine will continue to run. Hope this helps!

Posted on Jul 15, 2010

  • 130 Answers

SOURCE: Need gas/oil mix for Homelite 330 10604A, HJ

To the best of my recollection the 330 is an older model saw and should be running about a 16:1 ratio. 8oz. of oil to 1 gallon of fuel. Hope this helps.

Note: You're always better being a bit richer (lower ratio) than you are leaner (higher ratio).

Posted on Feb 20, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

What makes spark for plug?


In a 2 stroke the spark usually is generated by a magneto, coupled to a coil, rather than the voltage being supplied by a battery as in a car.

This is essentially a rotating magnetic field which produces a low voltage insufficient for the spark plug. That then is transformed to a high voltage by the coil, but with a low current, producing a fat spark for a fraction of a second.

So if the engine is hard to start, it could be

- worn piston rings causing low compression
- dirty air filter (doesn't take much in a 2 stroke)
- worn magneto breaker points (if fitted)
- cracked high voltage lead to the plug
- dirty or incorrectly gapped plug (discount this of course)
- mixture screws incorrectly adjusted

This may assist

https://www.youtube.com/watch?v=wIo_vfmN9jA
.

Nov 03, 2016 | Homelite Garden

2 Answers

I have got 26cc homelite hedge trimmer what type of 2 stroke oil do i need for it, MANY THANKS


You can use any brand of two stroke oil as long as it says on the container that it is suitable for air cooled engines and you need to mix it at a ratio of 25 to 1. Regards Phil

Apr 19, 2011 | Homelite Garden

1 Answer

What fuel does the homelite yard broom 2 take


depends if its 2 or 4 stroke if its 4 stroke the just regular gas if its two stroke then mixed gas and the ratio is 32:1

Jan 20, 2011 | Homelite 'Yard Broom' Leaf Blower

2 Answers

I cannot locate my owners manual and have not used the Homelite Ranger 16 inch in quite some time --- What is the fuel and oil requirement??


most 2 stroke Homelite chainsaws run on a fuel/oil mix of 50:1 --- But on some older model saws they say to use 40:1 mix.
I own several 2 stroke machines and I use 50:1 on everything and they all run fine ( even when they say 40:1 ).

c...

Jan 19, 2011 | Homelite ZR10926 16 Chain Saw

1 Answer

What is the air gap for my magneto on my 25cc homelite weeater?


Should be around .013 to .014. turn flywheel until magnets face magneto insert your feeler gauge and loosen magneto screws...let the magneto stick to the feeler gauge and the magnets... re-tighten the screws, remove feeler gauge, and you should be set...hope this helps. ;-D

Jul 06, 2010 | Homelite Mighty Lite Lawn Trimmer

1 Answer

Hi how to tune homelite 330 chain saw carby, idle


Before adjusting anything, check the fuel filter, air filter, and muffler for plugging. Check the condition of the fuel lines for decay or other damage. Tighten all carburetor fasteners. Make sure you have fresh fuel mix in the tank. Does the primer bulb pull fresh fuel into itself when pumped? Turn both jet screws CW to stops (lightly), then back out CCW 1-1/2 turns each. This is a basic setting and should allow the engine to start and run. Start the engine and allow it to warm up, then pull the throttle full on. Adjust H needle CW until the engine starts to speed up, but still 4-stroking. Proper final adjustment is when the engine 4-strokes unloaded, but immediately 2-strokes when cutting. Release the throttle and adjust L needle CW for fairly good idle, but still allows the engine to 'follow the throttle'. Adjust idle speed screw so that the chain stops turning, but the engine will continue to run. Hope this helps!

May 09, 2010 | Homelite ZR10926 16" Chain Saw

2 Answers

Cam timing my 2003 yamaha yz450 how do i do it


take magneto cover off find tdc on the magneto and look at the cams it should be after the inlet valve shuts and goes on the firing stroke just put a rod in the cylinder and see if the piston reaches the top off the bore when the magneto is at tdc then its fine buddy any probz im here to answer

Oct 08, 2009 | 2003 Yamaha YZ 450 F

1 Answer

What is the oil-gas mix for a homelite superxl chainsaw? For 1 gal.


16:1 ratio for most 2-stroke oil brands. A service manual recommends tro check the ratio marked on the bottle if using Homelite brand 2-stroke oil. For other oils, 16 parts of gas to 1 part of oil.

For 1 gal of fuel, that is 270cc of oil required to meet the 16:1 ratio.

Please rate this solution on FixYa!

Jul 16, 2009 | Homelite Garden

1 Answer

Homelite Mighty Lite Lawn Trimmer Magneto Air Gap setting 25cc


Normall setting is 10 thou but if there is no play in the crank bearings you can set at 8 thou

Jun 23, 2009 | Homelite Mighty Lite Lawn Trimmer

Not finding what you are looking for?
Homelite Consumer Products 9.0 Amp, 14 In. Chainsaw Logo

Related Topics:

25 people viewed this question

Ask a Question

Usually answered in minutes!

Top Homelite Garden Experts

roeb

Level 3 Expert

571 Answers

Roland W VanLue
Roland W VanLue

Level 3 Expert

486 Answers

Mike Squire

Level 2 Expert

420 Answers

Are you a Homelite Garden Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...