Question about Kyocera Mita KM-1650 All-In-One Printer

1 Answer

WHAT PWB MEANS - Kyocera Mita KM-1650 All-In-One Printer

Posted by Anonymous on


1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that got 5 achievements.


    An expert who has answered 200 questions.


    An expert who has answered 20 or more questions within one hour.

  • Expert
  • 245 Answers

Pwb means main power drive bord

Posted on Dec 24, 2014


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

2 Answers

How to fix C3100 Scanner carriage problem ?

C3100: ISU home position error
It usually means the scan carriage can't move.
If it s a little MFP, you can unlock the scan with the yellow button on the left of the glass (under the DP). (This was only meant for transport reason).
Otherwise - Possible cause:
Defective FFC between CCD PWB (YC1) and control PWB (YC8).
- Replace the image scanner unit (ISU)
Defective FFC between control PWB (YC6) and scanner PWB (YC103), or improper FFC insertion:
- Reinsert the FFC. Also check for continuity within the FFC.
If none, remedy or replace the FFC.
Defective home position sensor.
- Replace the home position sensor.
Defective harness between ISU motor and scanner PWB (YC104),
or improper connector insertion.
- Reinsert the connector. Also check for continuity within the connector harness. If none, remedy or replace the harness.
Defective ISU motor.
-Replace the ISU motor.

Mar 16, 2016 | Kyocera Office Equipment & Supplies

1 Answer

I have a Kyocera FS-4000DN Ecosys. I replaced the toner and now I get this. error 7410:0106690. Does anybody know what this means?

7410 Drum unit non- installing error The drum unit is not installed or not installed properly. The drum PWB EEPROM does not communicate normally. The drum unit is not installed. Install the drum unit (See page P.1-5-10). Defective connection drum PWB (YC1) and connect-L PWB (YC3). Check the connection of connectors drum PWB (YC1) and connect-L PWB (YC3). (See page P.1-4-9, refer to figure 1-4-5) Defective drum PWB EEPROM. Replace the drum unit (See page P.1-5-10). Defective engine PWB. Replace the engine PWB

May 26, 2015 | Kyocera Office Equipment & Supplies

1 Answer

Error c3200

It means the exposure lamp is not turned on. Either a connector has come loose or the exposure lamp and/or the inverter pwb and/or the control pwb must be replaced

Feb 07, 2014 | Kyocera FS-1118 Printer

1 Answer

I have an error code H401 on my sharp AR336 copier. Help please

H 401 means Heat roller low temperature detection. i.e. The temperature does not reach the
preset value within the specified time (3 min. in usual modes; 5 min. in curl correction mode.) after the power relay is turned on.
Possible causes
Thermister defective
Heater lamp defective
Control PWB defective
Thermostat defective
AC power supply defective
Interlock switch defective

Possible remedies
Check heater lamp for blinking with SIM5-2.
If lamp blinks properly:
Check thermister and its harness. Check thermister input circuit of control PWB.
If lamp does not light:
Check heater lamp for broken wire and thermostat for operation. Check interlock switch.
Check lamp control circuit of AC PWB and control PWB.
Clear the trouble with SIM14.

Jun 13, 2011 | Sharp Office Equipment & Supplies

1 Answer

I keep seeing U2 error code

U2 means some problems with your Eprom in the mcu pwb need to replace the EPROM, followed by MCU PWB, Rate this

Apr 28, 2011 | Sharp AR-5316 Advanced Digital Imager...

1 Answer

Can you tell me what service call 7002:0006904 on a Kyocera FS 5030N means? Thank you

7002 is the error code; 0006904 is the printer page count.

Error means-

Toner motor 2 overcurrent detection error (cyan toner)

• The engine controller PWB (A0004)

detected the overcurrent of toner
motor 2.

Possable causes-
1. Lump of toner inside cyan toner container or defectiveness of toner replenishment drive system.
Replace the cyan toner container.
2. Defective toner motor 2.
Replace the toner motor 2.
3. Defective engine controller PWB (A0004).
Replace the engine controller PWB (A0004).

Jan 05, 2011 | Kyocera FS1120D Laser Printer

1 Answer

Arm 205 display error F5 02 what this the solution for resetting ???/

the error F5 02 means that the copy lamp lighting is abnormal.
This is what is in the service manual:

F5 02 Content Copy lamp lighting abnormality
Details The copy lamp does not light up.
Cause Copy lamp error
Copy lamp harness abnormality
CCD PWB harness abnormality
Check and remedy
Check the copy lamp (SIM 5-3)
When the lamp lights:
Check the harnesses and connectors
between the CCD unit and the MCU PWB.
When the lamp does not light:
Check the harness and connector
between the copy lamp and the MCU PWB.
Replace the copy lamp unit.
Replace the MCU PWB.
Remarks Copy lamp disconnection
Cable is not attached.
You must call a tech to solv your problem.

Dec 01, 2010 | Sharp AR 201 Copier

2 Answers

Service Call 17H This pops up when I try to print multiple pages.

TONER RACK • If the toner cartridge does not rotate

rack rotation

Electrical components for detection of the malfunction
Rack motor (M2)
Rack clutch (CL1)
Rack home position sensor (PC4)
Master board (PWB-A)
Controller control board (PWB-P)

Step Remedy Reference
Control signal Location(electrical component)
1 Check PC4 operation. 149 PC4_ON 3-F
2 Check CL1 operation. 150 CL1_REM 2-F
3 Check M2 operation. 151 - 3-E
4 Replace PWB-A. - - -
5 Replace PWB-P. smileevil.gif

hope this helps

Jan 09, 2009 | Office Equipment & Supplies

1 Answer


Hello, the c6000 is the Fuser heater 1/2 defective --- but is you are getting the c6400 --- is a zero cross signal error which means defective PWB. You must replace the engine PWB or the power source PWB and check for correct operations.

The cheapest route would be to replace the fuser but with the c6400 code I believe you would just be throwing your money away.

Jan 05, 2009 | Kyocera KM-1505 Copier

2 Answers

Erroe code

You post a wrong printer nr, you must have bizhub C350 not bizhub 350, beacause 350 doesnt have that kind of code.
In Bizhub C350 that code means:
C12C0: Hard disk recognition error
You have the following options:
- reinstall the hard disk
- change hard disk
or as a last chance change PWB-MFP

good luck

Feb 06, 2008 | Konica Minolta bizhub 350 All-In-One Laser...

Not finding what you are looking for?
Kyocera Mita KM-1650 All-In-One Printer Logo

Related Topics:

36 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kyocera Mita Office Equipment & Supplies Experts

Kyocera HP Expert

Level 3 Expert

523 Answers

Henry Gertcher

Level 2 Expert

48 Answers


Level 3 Expert

76109 Answers

Are you a Kyocera Mita Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides