Question about Haier Washing Machines

1 Answer

Drum does not fill model #XQG50-11

I have a model #XQG50-11. The water runs right out the drain and barely any moisture to clothes. Cycles do not advance, I am assuming waiting on drum to fill. The water does not leak onto floor, but runs right out drain hose.

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 31 Answers

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 112 Answers

SOURCE: Tricity Bendix AW1400W front load. Water leaks

Ether the washer is over filling or has warn out the seals. If it has been abused (overloaded) it needs serious work. other wise the sensor may be stuck. Try 1/2 cup of vinegar with a load and see if that cleans the sensor travel area past the drum but inside the tub. This is a common problem for an old machine. Best leak is on the door and you may be able to tighten the screws but be careful it could mis aligne it so tighten a small amount and test by closeing the door. Do this at least twice before turning the screws hard.

Posted on Aug 17, 2009

ginko
  • 19396 Answers

SOURCE: Intermittent water on floor

Check the inlet valve hoses, even if inlet is at the back, the water may drip down and flow on the front part on the machine. There you also have the PUMP, a faulty pump may leak intermittently.
Here you get all diagrams and parts for your appliance.

Posted on Sep 25, 2009

beltronic205
  • 1456 Answers

SOURCE: I have water leaking out of the bottom of the

Could be damage to drum ie hole in it .Pour some water in to it with a kettle or alike, this should tell you..Is it quite old or has damage happened due to coin,,Kind regards...

Posted on Sep 29, 2009

  • 5 Answers

SOURCE: Maytag stack unit Model LSE7806ACE leaks

It is most likely the tub seal. Take the two phillips head screws out of the front cover located low on the cover lift forward and remove. Set the machine two low level and fill with water only no soap or clothes when unit starts agitating look at the bottom center of the clothes tub if water is leaking here then you will need to replace the tub seal and tub bearing assembly.

Posted on Sep 13, 2010

  • 9 Answers

SOURCE: Fisher&Paykel model GW711 top loader

why life so unfair ?

Posted on Jan 27, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Drum won't fill model #XQG50-11


check that your drain pipe is looped above the height of the drum.
if its lying too low to the floor, it will act like a syphon

May 08, 2014 | Haier Washing Machines

Tip

Washing Machine Problems and Repairs


Washing Machine Problems & Repairs If your clothes washer needs repair, you can begin your troubleshooting here A washing machine is basically a big tub that repeatedly fills with water and then drains, spins to wring clothes dry, and has a device for stirring things up-- either an agitator in the middle of a top-load machine or a rolling drum in the case of a front-loader. The four cycles that every washer performs are fill, wash, drain, and spin.
Though there are a number of problems that you can fix quite simply, washing machines have a variety of devices and controls that, when they go wrong, are better left in the hands of an appliance repairperson.
Some problems that commonly occur with a clothes washer are that it doesn't agitate; doesn't drain; doesn't run; shakes, vibrates, or moves; doesn't spin; the water temperature is wrong; or leaks.
If your washer doesn't run, be sure it's plugged in and that the receptacle works (the circuit hasn't overloaded). Before working on the washing machine, be sure to unplug it.
If it doesn't fill, the water inlet screens may be blocked. Clean or replace them. (Check your owner's manual for the location of the screens; they're often located at one end of the supply hoses, or you may have to remove a panel to access them.) Other reasons for not filling may be that either the timer or temperature selector is broken--both of these are repairs for an appliance repairperson.

If your washer doesn't spin, check to see if the clothes have jammed or are unbalanced in the drum before calling a repairperson. Unbalanced clothes will also cause a washer to shudder or “walk.” If straightening out the load doesn't stop the washer from shaking, look at the feet underneath and be sure they are properly adjusted to keep the washer sitting level on the floor (you just turn them to move them up or down).
To prevent problems, follow good maintenance procedures. Use the right amount of detergent for your washer and your water hardness, make sure the machine is level, and don't overload it for the cycle chosen.
Because washing machine hoses are under constant pressure, check periodically for wear because they can flood your home if they burst when you're away. You can prevent this by installing lever-type shutoff valves (shown top right). With these, you can easily turn off the levers for both hot and cold water between wash days.

on Sep 03, 2010 | Washing Machines

1 Answer

I have an LG Tromm Front Loader. Recently it has been running full cycles, but after completely draining, it begins to (VERY SLOWLY) fill up with water. For example, I run a load in the morning and by late...


If the drain hose has to rise very high then it is water left in the hose that is coming back in through the one way valve on the pump. If that is not the case, it is the inlet valve that has a bad seat on it and needs replaced.

Nov 04, 2013 | Washing Machines

1 Answer

My kenmore elite calypso washer won't fill up enough to get clothes completely wet.


It is possible that the machine does not start off the cycle because there are errors due to feedback from the inputs. For the program to start up the main program controller must initiate the INLET/MOTOR/DRAIN pump/ valve to open up and allow each function to be driven starting from the flow of water into the drum as also the drain valve to open to exit the water at the point of the program cycle. If this does not happen then the voltage at the valve/motor/pump must be checked or the fault relates to no voltage from the controller. This means the controller is a suspect.

Jan 17, 2013 | Kenmore Washing Machines

1 Answer

No water during any cycle.


if no water is coming in how is it agitating?is it filling at the beginning,then it starts to wash the clothes,now does it drain and then it won't fill again,send the model number and more info,

Jul 02, 2010 | Kenmore 24032\24036 Top Load Washer

1 Answer

LAT9604AAE No agitation but drum spins and drains water


cold possibly be just the agaitor but odds are u need a transmisson not worth repair

May 20, 2009 | Maytag PAV2300 Top Load Washer

1 Answer

Water fills drum (top loader) even when off


Your problem is a jammed water solenoid, If you take the top off the machine it is possible to remove and either strip it down to see if it is dirty or replace it. your washer hose usually connects directly to it.

Apr 11, 2009 | LG Washing Machines

1 Answer

Water drips out of front door


There does obviously need to be water in the drum to wash or rinse the clothes, however it may be the water level is now higher than normal , check for any blockages and check any drain pump filter.If all o.k. it may be the door seal is leaking .If under g/tee call maytag for repair

Jan 29, 2009 | Maytag Neptune MAH5500B Front Load Washer

1 Answer

Kenmore Washer Won't Drain


yes, check the drain, could be clogged, or check the water pump assembly as well, the clothe could be stuck in the impeller.

the burning smell could be coming from a separate electric water pump and it can not turn that is why it is burning already.


tnx 4 using fixya,

drcool

Oct 07, 2008 | Washing Machines

2 Answers

Spin cycle not working


try the door switch the washer will do everything but spin if the door switch is faulty

Jul 13, 2008 | GE Profile WPSR3120WWW

Not finding what you are looking for?
Washing Machines Logo

Related Topics:

48 people viewed this question

Ask a Question

Usually answered in minutes!

Top Haier Washing Machines Experts

Gerry Harvey
Gerry Harvey

Level 3 Expert

1456 Answers

Owen Barnes

Level 3 Expert

867 Answers

shaun taylor

Level 3 Expert

1525 Answers

Are you a Haier Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...