Question about Electrical Supplies

1 Answer

Perkins engine 40kva , the engine is do in overheating ever time and have change the gaskt two tax why

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    MVP:

    An expert that got 5 achievements.

    Habit-Forming:

    Visited the website for 3 consecutive days.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Contributor
  • 40 Answers

Make sure all of the vents, on the engine are free of dirt. Check carb adjustment and adjust as needed

Posted on Jun 17, 2014

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 11 Answers

SOURCE: diesel mixed with oil in the sump

You run again the generator but before running, check & mark the oil level. Then stop the generator & wait until the oil settle to the bottom of oil pan. Check the oil level again & if the oil level is higher than the marking before that's means you have an engine gasket leak.You need to replace that gasket.

Posted on Mar 21, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What is fault code #06 in EATON 40KVA?


Be clear what is the equipment of 40kva?

Sep 26, 2016 | Eaton Electrical Supplies

1 Answer

How to remove starter from a 4 cylinder perkins engine


Search Results

    [PDF]Perkins 4-154 Shop Manual

    www.kp44.org/ftp/Perkins_4-154_Shop_Manual.pdf
    88 Perkins. Engines workshop manual. 4.154. PRINTED lN U.S.A. .... removal, dismantling, assembly or refitting of a part is straightforward ... The ENGINE NUMBER is located on the cylinder ... starter motor, air cleaner, but without clutch. lb kg.

    Reliability built into starter motors - Perkins Engines

    www.perkins.com/en_GB/.../starter-motors.html

    Perkins EnginesYou can rest assured that your genuine replacement starter motor will work ... 4 Cylinder · 6 Cylinder ... You can learn more about these cookies and general information about how to change your cookie settings by visiting our Privacy and Cookies page. ... This need for dependability is why we test each of our starter motors.

Dec 25, 2015 | Cars & Trucks

1 Answer

How do i align the timing gear on my perkins dk 51280 engine


Timing gears? have you pulled it that far apart? On timing gears there are usually stamped onto the gears a small dot. lign them up. Not sure why tore down so far? If you take off the diesel pump align the timing marks in the small window plate first else you will be in a mess.

Aug 25, 2013 | Pramac GBW30P Encl Diesel Genset w/Perkins...

1 Answer

Rough idle 01 overheats


blown head gaskt most likely check for a loss of engine coolant would cause overheating and rough idle

May 07, 2013 | 1998 Ford Windstar

1 Answer

Perkins p3 desiel engine manual


what are the perkins p3 engine specs

Oct 17, 2010 | Garden

1 Answer

Perkins 3 cylinder powered pramac generator


Start looking at your safety circuits.

1. High water temp
2. Low Oil
3. Low water etc...

From the manual these are the protection circuits.

• Engine protection: low oil pressure, high engine temperature.
• Genset protection: under/over voltage, overload, battery charger failure, battery voltage out of limits,
under/over frequency, start failure.
• Circuit breaker protection: IV poles.
• Differential protection.


Any one of them will trip the fuel relay closed. What you may be able to do is disconnect one at a time each protection circuit and see when the fuel relay opens. (Make sure to reconnect each one if it had no effect on the fuel solenoid)

Once you isolate which circuit it is in then you can chase wires or change the bad switch.

Thanks for choosing FixYa.

Kelly

May 24, 2010 | Pramac GBW30P Encl Diesel Genset w/Perkins...

1 Answer

My 92 Legend runs rough after valve cover gasktes were changed. It runs rough after it warms up almost like its off balance. It feels like the engine misfires.


Are you sure you put the spark plug wires back in the correct place. And pull out the spark plugs and make sure they are ok.

Nov 06, 2009 | Microwave Ovens

2 Answers

Diesel mixed with oil in the sump


You run again the generator but before running, check & mark the oil level. Then stop the generator & wait until the oil settle to the bottom of oil pan. Check the oil level again & if the oil level is higher than the marking before that's means you have an engine gasket leak.You need to replace that gasket.

Mar 19, 2009 | Pramac GBW30P Encl Diesel Genset w/Perkins...

Not finding what you are looking for?
Electrical Supplies Logo

Related Topics:

81 people viewed this question

Ask a Question

Usually answered in minutes!

Top Electrical Supplies Experts

Steve

Level 3 Expert

3287 Answers

Gene Haynes

Level 3 Expert

5089 Answers

Brad Brown

Level 3 Expert

15441 Answers

Are you an Electrical Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...