Question about Stanton STR8-80 Turntable

1 Answer

How to remote start stanton str8-80 - Stanton STR8-80 Turntable

Posted by Anonymous on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

  • Expert
  • 432 Answers

A cable in your turntable , which you connect with your mixer and in the manual it says how to allocate the remote start to a fader / knob.
It's in the manual, except if your ain't able to it.....

Posted on Oct 22, 2014

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a stanton T62 turntable. Why does it start off slow and sounds like its dragging


Defective motor controller or motor for the platter. Also check the drive belt is so equipped.

Oct 24, 2017 | Stanton Audio Players & Recorders

1 Answer

Speed has gone fast


www.stantondj.com/contact-stanton.html

Jun 30, 2014 | Stanton STR8-100 Turntable

1 Answer

Stanton st.150 turntable sins unevenly


That is a lack of maintenainance, but your real problem is that your

voltage regulator from -24 en 24v gets to hot, since the stanton has crappy everything, where cheap build and often the components aint screw against the cooling block, so first check that and well , there about 60 crappy su\'scon caps that needs replacement. It\'s a tt from hell with the useless weight. Your system started spinning hard, cause the thermal protection started to work. Overheating, since most peoples set the start and stop torque set at the highest point, and with the small cooling blocks you get a problem and by pressing the platter, you ask for more current and that was just too much, if your bearings were that bad you assume , you have heart a lot more noice.

gr richard

Apr 01, 2014 | Stanton ST-150 Turntable

1 Answer

How can i fix the start button on my stanton str8-100 if its stuck?


Replace the spring or just open the unit and lubricate a. bit, the spring that is....

Mar 20, 2013 | Stanton STR8-100 Turntable

1 Answer

What's a good needle for a Stanton STR8-30?


Hi, Stanton 500AL or 505v3. You can't go wrong. We have them in stock. Sstyluscity@gmail.com

Mar 02, 2011 | Stanton STR8-30 Turntable

1 Answer

Hey guys I purchased the Stanton Str8-80 in 2003 and used it actively for the following 1 or 2 years. Shortly after that, I left it in a corner to collect dust and only recently, I started to use it again....


If the turntable has a belt drive, the belt probably has failed. If direct drive, the motor may have failed. Only a cheap turntable would have rim drive that failed. Your Stanton is not one of them.

Apr 26, 2017 | Stanton STR8-80 Turntable

2 Answers

STANTON C324 NO DISK \r\nTHIS FIX THE PROBLEM AND COST YOU $25 NO LIKE IN STANTON $320 ;) http://cgi.ebay.com.au/ws/eBayISAPI.dll?ViewItem&item=290406538324&ssPageName=STRK:MEWNX:IT


You need a new laser or laser mechanism. You can order one online no problem. The part number is: Sony KSS 213Q. make sure there is a Q at the end of it because sony makes a lot of different laser types and the one inside the Stanton C.324 is the Q. Yes the C.324 has Sony guts. You might also want to look into ordering a RF Signal Processor Chip. the part number is: CXA 2581N. Once again make sure the part number ends with a N. This part you might have a little more trouble finding online but it is possible. The laser mechanism you can find on Ebay for about 20$ to 30$ and if you order it from stanton magnetics it will run you about 200$. The signal processor I bought the other day from a Sony parts Dealer in my home town for 20$. Im having an Electronics Repair place do it for very cheap. If you send your stanton c.324 to stanton magnetics you will end up paying more than the turntable is worth brand new unless you have valid warranty still on it.

Hope I could help you with the problem. Cheers.

Jun 15, 2010 | Stanton C314 Tabletop CD and Mp3 Player

Not finding what you are looking for?
Stanton STR8-80 Turntable Logo

Related Topics:

82 people viewed this question

Ask a Question

Usually answered in minutes!

Top Stanton Audio Players & Recorders Experts

 Grubhead
Grubhead

Level 3 Expert

5190 Answers

da surgen

Level 2 Expert

92 Answers

Electro Med Services...
Electro Med Services...

Level 3 Expert

6694 Answers

Are you a Stanton Audio Player and Recorder Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...