Question about Whirlpool Duet GHW9150P Front Load Washer

Open Question

I,m getting f31 on whirlpool dryer model wed9400

Posted by Anonymous on

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 3 Answers

SOURCE: How do I reverse the

It's mechanically reversible, but requires a right-hand hinge cover plate (not included with basic purchase) in order to fit properly. The RH hinge cover is part number W10181197. The reversal instructions are supplied by whirlpool when you order the door reversal kit.

If you can't find the hinge cover or whole door reversal kit, or just don't want to buy it; you could trim the LH hing cover by hand, or leave it off and cover the hole into the interior with some tape or something

Posted on Mar 22, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Whirlpool Cabrio dryer. F31 low voltage code. No breakers are tripped. Reset them anyway. Still no heat. Ideas?


We are very sorry to hear this and we apologize for the inconvenience this has caused you. We would be glad to look into this if you could email us at Whirlpool_Digital@Whirlpool.com with your name, address, phone number and the model & serial numbers of the Dryer.

Jan 25, 2017 | Whirlpool Dryers

1 Answer

Why does my whirlpool duet dryer door keep popping open? After a few minutes, the top latch of the dryer pops open and the dryer stops. Visual inspection of the dryer yields no issues. The door has...


The latch is shot I would replace both top and bottom. Most of the time all you need is a needle nose plier to perform the task. There are some good tutorials online that walk you through the steps. The actual latches a fairly inexpensive and you should be able to find them from a supply store that specifies in home appliance repair.

Jul 28, 2014 | Whirlpool WED9400S Electric Dryer

1 Answer

F25 error code


The "F25" error code means the control board senses the inlet thermistor shorted. The inlet thermistor is a part of the hi-limit thermostat which is located on the heating element box.

- The hi-limit thermostat kit Part number: AP3094323

Read more: http://forum.appliancepartspros.com/dryer-repair/54078-whirpool-duet-dryer-error-code-f25.html#ixzz2n2Rmgm7a
http://forum.appliancepartspros.com

Dec 10, 2013 | Whirlpool WED9400S Electric Dryer

1 Answer

Kenmore elte oasis electric dryer error code f31


f31 code is a thermistor problem ,if you need help go to www.appliancerepairservice.com

May 22, 2012 | Kenmore Dryers

1 Answer

Whirlpool Duet dryer runs way too hot, even during air only cycle.


sounds like restricted air flow to me . check filter and the vent for plugged pipe

Apr 18, 2012 | Whirlpool WED9400S Electric Dryer

1 Answer

How do I reverse the door on my Duet WED9400 dryer?


It's mechanically reversible, but requires a right-hand hinge cover plate (not included with basic purchase) in order to fit properly. The RH hinge cover is part number W10181197. The reversal instructions are supplied by whirlpool when you order the door reversal kit.

If you can't find the hinge cover or whole door reversal kit, or just don't want to buy it; you could trim the LH hing cover by hand, or leave it off and cover the hole into the interior with some tape or something

Mar 06, 2011 | Whirlpool Duet GHW9150P Front Load Washer

1 Answer

Whirlpool front loading duet washer stops at the rinse/spin cycle door then locks. code F31 comes up. would this have something to do with the main board?


Hello

Error F31 in your whirlpool duet washer is displayed due to MCU (Motor Control Unit) failure. It is displayed if the heat sink gets too hot and then the MCU stops motor, then MCU sends the signal to CCU (Central control unit). Please check the wire connections between the CCU and MCU, if thats fine then check the motor operation. Hope you understand...replacing the part# that has gone bad is recommended repair. Please get back to me if you have any other questions.

Kevin

Nov 10, 2010 | Whirlpool Duet GHW9150P Front Load Washer

Not finding what you are looking for?
Whirlpool Duet GHW9150P Front Load Washer Logo

Related Topics:

13 people viewed this question

Ask a Question

Usually answered in minutes!

Top Whirlpool Washing Machines Experts

Dan Webster
Dan Webster

Level 3 Expert

8220 Answers

Sal DeAngelo

Level 3 Expert

2122 Answers

yadayada
yadayada

Level 3 Expert

75797 Answers

Are you a Whirlpool Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...