Question about Baby Lock Imagine

Open Question

Lock Jet -Air Threading is not drawing thread through into looper

Posted by Anonymous on

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 13 Answers

SOURCE: I've lost my manual and video need threading info

One of the most common mistakes with overlockers is that the threads must always be threaded in order. So if you sew about 1 inch and the thread breaks try unthreading the eyes of the needles rethread the looper and then rethread the eyes of thew needles. If not you will get the same result of sewing about 1 inch and it will break again.

Posted on Aug 27, 2008

  • 4 Answers

SOURCE: Baby Lock Evolve wire Looper threading tool

You have to get the replacement wires from a Babylock dealer, I did too then after sticker shock at the price of that wire I learned to make a thread cradle and use that to thread difficult threads no. Take about 24 inches of regular sewing thread and fold it in half, put the open ends (together, same legnth) into the jet air port and hold onto the loop end, press the jet air threader and it will thread the machine, insert the thread you want to use into the loop you have in your hand and pull it thru the machine using the ends of the thread you put thru the machine, sounds harder than it is and works all the time. No more spending $8 on replacement wires. You can use this method for all the jet air sergers.

Posted on Dec 07, 2008

  • 1116 Answers

SOURCE: I need a new looper threading lever for the

This is the lever on the air-jet threader?

You might try the sew4less website, but may have to go to the BL dealer for this.

Posted on May 01, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a Baby Lock Evolve and the tread is not blown right through the loop. What should I do?


These air-threading loopers can be used while the 'blast door' is one so that you may observe how the thread behaves as it passes through the system. Note that the rods that are controlled by the looper threader setting must join together and that there must be a sufficient amount of loose thread to blow all the way through.
If these steps continue to fail your next best step is to have a technician look at it. It is possible that not enough air is blasting through to complete the threading process.

Apr 26, 2017 | Baby Lock Sewing Machines

1 Answer

I have a white speed lock 234 serger and cannot get it to chain off. The thread bunches together


Yes, thread the upper looper first, the lower looper next.

***Make sure that you have the presser foot RAISED during the ENTIRE threading process until you get to the point of threading the needles.

The second to last step in the lower looper process is to make sure lower looper thread DRAPES over the top of the upper looper & thread, then both thread tails get pulled under the presser foot and toward the back of the machine.

Give each thread a little extra tug as it goes through the tension disk to make sure it is seated. Verify that all the threading steps have been followed. Any skipped steps, extra thread wraps, or incorrect threading will most likely cause a problem.

Make sure you have brand new needles before threading. If one is bent or damaged, you will probably have issues with skipped stitches.

Set all the tensions to the midway point (the factory standard for regular chain stitch). The tensions can then be tweaked when the machine is correctly creating a chain.

If the machine messes up, breaks a thread, comes unthreaded, etc., save yourself some time and frustration and RETHREAD everything from the beginning. Trying to rethread out of order usually fails!!!

Once you are more comfortable with your machine, you can try fishing a thread, but even experienced serger users still have trouble with this.

...

Aug 03, 2016 | Sewing Machines

1 Answer

The tread from the lower looper is not being picked up by the upper looper how o i fix this?


Best advice would be to consult your owner's manual. The most common serger problems are caused by incorrect threading or not threading the threads in the proper order. With most sergers, the upper looper should be threaded first. The lower looper is threaded second and the lower looper thread tail should drape OVER the upper looper. Then thread the needles.

Be sure when threading that each thread is pulled snugly into the tension disks.

...

Nov 15, 2015 | Janome MyLock 644D

1 Answer

I need a new looper threading lever for the Imagine Baby Lock


This is the lever on the air-jet threader?

You might try the sew4less website, but may have to go to the BL dealer for this.

May 01, 2010 | Baby Lock Imagine

2 Answers

My Bernina Serger 800DL is not sewing right. I have threaded it twice and it still doesn't work. Can you help me with this problem??


Sometimes you have to remove all the thread and start over.

Make sure:

The needles are inserted properly.

The thread antenna is fully extended.

The loopers are at their highest position.

The presser foot is up.

The tensions are open/zero.

Begin threading from the right to the left.

Good luck - I gave in (and saved the life of my old serger) and bought an air-jet threading serger.

Apr 27, 2010 | Sewing Machines

2 Answers

My serger will only sew a few inches, then the thread on the lower looper breaks. I have checked threading, rethreaded many times.


Been there, done that. Old serger almost went out the window more than once.

Raise the thread antenna and loopers to their highest positions.

Set the tensions to zero. If your serger has auto-tension, raise the presser foot as this also opens the tensions.

Begin threading from the right as indicated in your manual or on the door of the serger.

If this continues, the serger may need to be serviced as the timing could be the problem.

Ask before leaving the serger as the service cost usually starts around $100.

I finally gave in and bought a Babylock with instant jet-air threading.

Apr 01, 2010 | White Sewing Speedylock 1600 Mechanical...

1 Answer

Baby Lock Evolve wire Looper threading tool


You have to get the replacement wires from a Babylock dealer, I did too then after sticker shock at the price of that wire I learned to make a thread cradle and use that to thread difficult threads no. Take about 24 inches of regular sewing thread and fold it in half, put the open ends (together, same legnth) into the jet air port and hold onto the loop end, press the jet air threader and it will thread the machine, insert the thread you want to use into the loop you have in your hand and pull it thru the machine using the ends of the thread you put thru the machine, sounds harder than it is and works all the time. No more spending $8 on replacement wires. You can use this method for all the jet air sergers.

Oct 03, 2008 | Baby Lock Evolve

1 Answer

I've lost my manual and video need threading info


One of the most common mistakes with overlockers is that the threads must always be threaded in order. So if you sew about 1 inch and the thread breaks try unthreading the eyes of the needles rethread the looper and then rethread the eyes of thew needles. If not you will get the same result of sewing about 1 inch and it will break again.

Aug 26, 2008 | Baby Lock Ellure

2 Answers

Threading a husqvarna huskylock 1001L serger


Solution taken from "Handbook for Huskylock Sewing Machine Models 1001L/1000L/1000"

1. Raise the presser foot by using presser foot lever. When the presser foot is raised, the two thread tension discs in the thread tension control panel are released so that thread passes freely between them. Otherwise thread tension may not be correct.

Important! When threading the needle, always be sure to lift the presser foot lever, and also take care to thread in the proper order.

Threading order:
1. Upper looper thread (green)
2. Lower looper thread (blue)
3. Double chain stitch looper thread (purple) in case of 5 thread stitch or double chain stitch
4. Right needle thread (red)
5. Left needle thread or double chain needle thread (yellow)

Caution!
Because the left thread tension dial (yellow) is used for either the left needle or the double chain stitch needle, these needles will never be used at the same time.

Upper looper (green) sequence:
1. Thread holder (silver triangle openings attached to thread holder stand)
2. Thread guide (flat silver clips just behind thread tension disc)
3. Thread tension disc (circular knobs with numbers for tension setting)
4. Pull thread around upper looper guide and upper looper
5. Pull thread into hole of upper looper

Lower looper (blue)
Repeat 1, 2, 3.
4. Pull thread around guide (see color coded chart inside front serger cover).

Easy threading mechanism (for lower looper)
1. Pull out the lower looper threading lever
2. Thread the lower looper and position the thread on hook of the lower looper
threading lever.
3. Push the lower looper threading lever back to its basic position while
holding the end of the thread.

Caution:
When returning the lower looper threading lever, always make sure that the two
blue triangle marks (directional arrows) meet each other.

Right needle thread (red)
Left needle thread (yellow)
Important: Thread the needles after threading of lower looper and upper looper.
First raise the presser foot lever, and then thread the needle threads in order shown in color coded thread guide.




Jun 24, 2008 | Sewing Machines

1 Answer

Does not stitch lower thread


Make sure when you thread the machine you have the thread seated into the tension assembly on top, then make sure you have the threading ports locked and the switch in the proper place for each looper threading, the machine will only partially thread if you do not have the port locked and it will even still sew although not properly.

May 25, 2008 | Baby Lock Imagine

Not finding what you are looking for?
Sewing Machines Logo

Related Topics:

35 people viewed this question

Ask a Question

Usually answered in minutes!

Top Baby Lock Sewing Machines Experts

Tally Girl
Tally Girl

Level 3 Expert

1122 Answers

Chris Wetmore

Level 2 Expert

185 Answers

SewTechWayne
SewTechWayne

Level 2 Expert

186 Answers

Are you a Baby Lock Sewing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...