Question about Kodak Office Equipment & Supplies

1 Answer

My kodak esp 6100 keeps on showing error code 3806?

Kodak esp 6100 offie aio printer Kodak sev,# h119118 error code 3806 reinstalled printerhead an ink cartages but same code comes up.

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 43 Answers

Disconnect power cord, let it set 30 sec, reinstall cord. If problem still there pull out the printheads and reinstall, may have to do this a few times, if problem still there may need printheads.

Posted on May 08, 2014

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Joed911
  • 4338 Answers

SOURCE: my printerhead on my kodak aio 5300 is worn out.

This is a common problem with these units. contact Kodak at 1-800-421-6699.
Kodak will send you a new one.
Then follow the instructions on this link to replace the print head:
http://www.kodak.com/global/plugins/acrobat/en/service/manuals/AiOPrinters/printhead/AUR1780-9_UE_RevC.pdf

Click on this link or copy and paste the complete link into your browser.
If I could be of further assistance, let me know. If this helps or solves the issue, please rate it.
Thanks, Joe

Posted on Jun 25, 2009

  • 15 Answers

SOURCE: Kodak 5100 AIO won't print after cartridge change

the red blinking light indicates that your printer wont recognize your ink carthridge. you can try to reseat the carthridge and the printhead. to remove the printhead just press on the release tab which is located on the upper left corner of the printhead wall. If this will not correct the issue, you need to call their technical support hotline. maybe the carthridge is faulty or there is a problem on the printhead. their hotline no is 1 800 421 6699

Posted on Aug 28, 2009

  • 295 Answers

SOURCE: reset chip kodak esp 7 ink cartridge

Kodak printer works with genuine Kodak cartridges and that too brand new not refilled cartridges. The brand new cartridges have a certain code that is recognised by the Printer.Kindly buy genuine cartridges as the printer may be damaged by Non comaptible cartridges.

Posted on Sep 21, 2009

  • 15 Answers

SOURCE: My Kodak ESP 3 all-in-one printer will not print

you may try to clean the printhead and recalibrate the printer. if this will not correct the problem, you need to replace the printhead. I suggest contacting Kodak technical support to have a replacement printhead.

Posted on Apr 17, 2010

damnor01
  • 1179 Answers

SOURCE: My esp 3 kodak printer

Your printer needs a service, in other words the waste ink sponges need to be cleaned and dried. They then need to be replaced and the printer reassembled. Then the Epson counter resetting software needs to be installed.

With this software the printer can be set to zero, it will work perfectly after this bit of attention.
It is a good printer, it's nothing that can't be repaired.

A computer technician will be more than happy to service your printer for you.

All the best!
damnor01

Posted on Feb 01, 2011

Testimonial: "Thanks for the detailed info. Sorry to see that'll take a tech to repair it. It may be cheaper to buy a new printer."

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What is error code 3806?


Error Printer error 3806 3807 3808 3809 3810 or 3811

Kodak does not say what the error is but they do show how to deal with it.

Nov 29, 2015 | Kodak ESP Office Equipment & Supplies

1 Answer

Kodakesp3250 has error code 3806 after installing new cartridges?


Sorry this is a system failure error . this sometimes can be resolved with a new printhead. otherwise contact kodak for a replacement.

Jul 06, 2014 | Kodak Esp 3250 Allinone Multifunction ( ...

1 Answer

Kodak ESP 3250 says Printer Error. Error Code 3806


According to the Kodak website, you should follow this procedure:

  1. Disconnect the power adapter from the printer.
  2. Wait 30 seconds to allow the printer to reset.
  3. Connect the power adapter to the printer. Turn on the printer, if necessary.
If the error continues:
  1. Open the printer access door.
  2. Remove and install the printhead two times.
  3. Close the printer access door.
  4. Wait until the printer is ready to use.
  5. If the error is displayed, contact Kodak

Sep 20, 2013 | Kodak Office Equipment & Supplies

1 Answer

Hello my name is Amy and i recently had to do a complete system recover to my pc, Well when i went to reinstall my Kodak ESP.3 All-in-One Printer it loads the bojour and when it starts to install the Kodak...


Before you try re-installing it again, restart your computer. Sometimes installed programs require restart even if they don't force it on the user.
After restart try installing the software again, if it fails with the same error then your installer may be corrupt or not suitable for your OS. Go to the Kodak website and download the latest software and drivers for your printer. Here is the link. You will have to click on the right side on Downloads to select your OS and then search for ESP 5 will show up the results.
If you get the same error, check to see if you have the latest Service Pack installed (do a System Update for MAC). Update your computer and try again. By this time you have everything up to date and if it still won't work I'd say that there must be something corrupt into your OS.

Dec 05, 2010 | Kodak ESP 5 Printer

2 Answers

Error code 1- 2036


I fixed my error code 1-2036 by going to the "Configure Settings" in the AiO Home Center then selected AiO Printer changed to "Print Quality" to Draft and clicked OK.... Then I was able to Scan with no errors. I think the config settings were corrupted some how and this resaved them properly.
if that doesnt help
Go to Control Panel
Double Click on Printers and Other Hardware
Double Click on Scanners and Cameras
Double Click on Kodak 5100 AiO
Click Next
Read and follow directions
if both the solutions doesnt help... its time to call kodak

Jul 10, 2009 | Office Equipment & Supplies

1 Answer

I keep getting error 1-2070


Resolution
Check to see if the required files are present:
  • Go to C:\WINDOWS\system32\kodak. Check for 2 folders "kds_aio5000(for AiO 5000 series printers) and kds_aioesp(for ESP series)
  • Depending on printer model, open kds_aio5000 or kds_aioesp.
    • For kds_espaio it should only have the lib folder. It doesn't have the ekaiowia.dll
  • Inside the lib folder it should have cct.ekpgct, hippo.dll. Both for kds_aio5000 and kds_aioesp.
  • If hippo.dll is missing then try the following:
Option 1: 1. Go to C:\Documents and Settings\All Users\Application Data\Kodak\EasyShareSetup\printer\scanner 2. Right click on aioscnnr.msi and choose uninstall once this is finished reinstall it by double clicking on the same msi file. 3. Check to see if the scanner files are now present (see above) if not then go to Option 2 Option 2: 1. Insert the Home AiO CD. Go to CD rom drive\printer\scanner 2. Right click on aioscnnr.msi and choose uninstall once this is finished reinstall it by double clicking on the same msi file. 3. Check to see if the scanner files are now present (see above) if not then go to Option 3 Option 3: (manual installation) 1. Go to C:\Documents and Settings\All Users\Application Data\Kodak\EasyShareSetup\printer\scanner or on CDROM drive ..\printer\scanner 2. Open the aioscnnr.cab file then look for the missing file(files needed: cct.ekpgct, hippo.dll, and ekaiowia.dll) Extract the files anywhere on to the computer (Desktop is preferable). 3. Copy the cct.ekpgct, and hippo.dll to C:\WINDOWS\system32\kodak\kds_aio5000\lib 4. Copy the ekaiowia.dll to C:\WINDOWS\system32\kodak\kds_aio5000

Apr 12, 2009 | Kodak ESP 5 Printer

Not finding what you are looking for?
Office Equipment & Supplies Logo

Related Topics:

92 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kodak Office Equipment & Supplies Experts

Les Dickinson
Les Dickinson

Level 3 Expert

18391 Answers

Doctor PC
Doctor PC

Level 3 Expert

7733 Answers

Cindy Wells

Level 3 Expert

5099 Answers

Are you a Kodak Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...