Question about Husqvarna , No.455 Rancher, 20" Gas - Powered Chainsaw

1 Answer

How to check the ignition coil? - Husqvarna , No.455 Rancher, 20" Gas - Powered Chainsaw

Posted by Anonymous on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Cheetah:

    An expert who has answered 20 or more questions within one hour.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Husqvarna Expert
  • 188 Answers

To properly check the coil takes an expensive machine. Coils have a very low failure rate. However, if you doubt the coil, they are not terribly expensive. If you swap the coil make sure to properly set the air gap (distance from the fly wheel) and clean the area the coil mounts. Failure to get a good ground at the mounting location will prevent the coil from performing properly.

Posted on Feb 03, 2016

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

No spark from coil to distrubuter


Disconnect the ignition coil output wire at the distributor cap.
Connect a spark plug to the end of the ignition coil output wire which you just disconnected.
Connect a ground wire to the threaded portion of the spark plug.
Disconnect the ignition coil ground wire from the negative terminal on the coil (Green Wire).
Connect one end of a ground wire to the ignition coil negative terminal.
Turn the ignition switch to the ON position.
Tap the other end of the ignition coil ground wire jumper on an good grounding point (for example the battery negative terminal) and look for sparks at the spark plug that correspond to the frequency of your tapping of the ground wire.
If you have a good spark at the spark plug, the ignition coil is good.
If you don't get a good spark, check for approximately 12 VDC from the coil positive terminal (black wire) to ground with the ignition switch in the ON position. You should also get approximately 12 VDC from the coil negative terminal (Green wire) to ground
Ignition Coil Resistance Check

In addition to the test above, you may elect to perform an ignition coil resistance check as confirmation of the coil's condition.

Check the ignition coil primary coil resistance by connecting an ohmmeter between the positive (Black wire) and negative (Green wire) terminals on the coil. The resistance should be 0.4 to 0.6 ohms.
Check the ignition coil secondary coil resistance by connecting an ohmmeter between the coil output terminal and the ignition coil negative terminal. The resistance should be 5000 to 7200 ohms.

You may have a bad coil or bad ground or wire connection

Jan 23, 2017 | Cars & Trucks

3 Answers

Engine stop


If theres no spark from the spark plugs then you would have to replace them?

Jul 12, 2008 | 1993 Toyota Corolla

1 Answer

00 dodge dakota 4.7 codes p0353 and p0354 what that mean


code p 0353 refers to ignition coil C primary/secondary --circuit malfunction===causes ---wiring--ignition coil---ECM
code p 0354 refers to ignition coil D primary/secondary ---circuit malfunction===causes --wiring---ignition coil---ECM
check harness connections to the coils are clean and tight
replace the coils
check connections to the ECM

Nov 19, 2016 | Dodge Cars & Trucks

2 Answers

Changed everything for tune up still no spark


What make , model an year vehicle ? Is it coil on plug ignition system or dis ignition . Did you test for battery voltage at the coil or coils ? Is the powertrain control module controlling the coils ? Does it have a ignition control module ? Automotive Engine Ignition Coil Testing Repair How to test an ignition coil and ignition module with test light

Mar 17, 2015 | Cars & Trucks

1 Answer

2005 cavalier 2.2 /no spark


check ignition coil see if its getting battery power check black and pink ignition wire going to ignition coil.if you not getting power check the 20AMP ignition fuse.if power going to ignition coil, problem could be bad ignition coil or bad ignition module or pcm problems, best have vechicle code scan for pcm fault or crankshaft position sensor or ignition module fault.

Sep 29, 2012 | Chevrolet Cavalier Cars & Trucks

1 Answer

2000 silverado 1500 no spark


check ignition fuse to coil and check see if power getting to coil if yes ignition coil or ignition module faulty.if no power getting to coil and ignition module more likely you have blowed ignition fuse or faulty wiring from ignition fuse box terminal to the ignition coil and module.

Nov 06, 2011 | 2000 Chevrolet Silverado 1500

1 Answer

How do you check an automobile Ignition Coil on a 1973 Datsun 240 Z when the ignition coil is't connected to the automobile electrical system? Can this be done? If so please tell me How!!!!!!! THANK YOU...


    1. To check the coil's primary circuit, perform the following:
    1. Make sure that the ignition switch is turned OFF .
    2. Remove the primary wires from the (+) positive and the (-) negative terminals of the coil.
    3. Using an ohmmeter, set it to the 1.0 ohm range, then connect the probes to the primary terminals. The resistance should be 0.84-1.02 ohm's; if not, replace the ignition coil.

    1. To check the coil's secondary circuit, perform the following:
    1. Make sure that the ignition switch is turned OFF .
    2. Remove the coil wire from the center terminal of the coil.
    3. Using an ohmmeter, set it to the 15,000 ohm range, then connect the one probe to the center terminal and the other to the (-) negative terminal. The resistance should be 8,200-12,400 ohms. If not, replace the ignition coil.
  • Jan 22, 2011 | Datsun 210 Cars & Trucks

    1 Answer

    I have no spark in cylinders 2,4,6 on my 2002 Ford escape and three codes 354,355,356 Which means the same . After checkin those Three coils I found out , there is no negative Any advise?


    P0354 - Ignition Coil D Primary/Secondary Circuit Malfunction.

    Description of DTC:
    The ignition signal from the Powertrain Control Module (PCM) or Electronic Control Module(ECM) is sent to and amplified by the power transistor. The power transistor turns ON and OFF the ignition coil primary circuit. This ON/OFF operation induces the proper high voltage in the coil secondary circuit.

    Symptoms:
    - Lack/Loss of Power
    - The engine may be harder to start
    - Engine hesitation
    - Check Engine Light On
    - No spark

    Possible Causes:
    - Open or short in the ignition coil circuit
    - Ignition coil circuit shorted to ground
    - Ignition coil connector
    - Damaged ignition coil
    - Damaged PCM or ECM

    Possible Solutions:
    - If damage, repair ignition coil circuit
    - Replace ignition coil
    - Replace PCM or ECM



    P0355 - Ignition Coil E Primary/Secondary Circuit Malfunction.

    P0356 - Ignition Coil F Primary/Secondary Circuit Malfunction.

    Jan 18, 2011 | 2002 Ford Escape

    3 Answers

    Po351 jeep


    p0351 is ignition coil primary circuit this USUALLY means a bad ignition coil use only a name brand coil ,but it could be a bad computer but not very common

    Sep 21, 2009 | 1996 Jeep Grand Cherokee

    1 Answer

    I cannot get a spark on the plug .Can you tell me how to dismantel the magneto for checking


    Hi there
    First you have to measure the resistence between the lead wire and iron core on the ignition coil . To find the ignition coil just follow the spark plug wire . Depending on the model you have the ignition coil is usually 2 bolts holding it on place . Check with the manufacture what is the resistence (ohm) you should have on the coil and if you have the correct resistence readjust the ignition coil with the flywheel . To readjust the coil get a piece of paper and put it between the ignition coil and flywheel , tight the 2 bolts and remove the paper . if still no spark you have to replace the ignition coil .
    Hope this help

    Sep 02, 2009 | Garden

    Not finding what you are looking for?
    Husqvarna , No.455 Rancher, 20" Gas - Powered Chainsaw Logo

    92 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Husqvarna Garden Experts

    Phil Walker
    Phil Walker

    Level 3 Expert

    608 Answers

    Doctor PC
    Doctor PC

    Level 3 Expert

    7733 Answers

    Roland W VanLue
    Roland W VanLue

    Level 3 Expert

    486 Answers

    Are you a Husqvarna Garden Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...