Question about Jet 3 Ultra Power Chair

1 Answer

How do u fix a pronto m51 wheel chair joystick after it got wet and it flashes 7 times

Posted by Anonymous on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Master:

    An expert who has achieved Level 3.

  • Jet Master
  • 401 Answers

I would dry it completely and try it again. it may need to be opened and dried on the inside, or replace the joystick.
Strege Mobility

Posted on Oct 10, 2017

Ad

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

Ad
  • 103 Answers

SOURCE: How do I get the battery out of the wheel chair

Take the seat off and the batteries should lift out

Posted on May 26, 2009

  • 29 Answers

SOURCE: pride mobility Jet 3 Ultra Power Chair 7 flashing

a 7 Flashe code. There is a joystick fault. Make sure the joystick is in the center position and then power off and on again. Check all your couplings. make sure when turning on the unit you only mash the power button for 1 sec. 2-3 sec will put the unit in "Lock out mode".
This ierror will also be present if the joystick is off center when powered up. If you experience these symptoms, you must first make sure there is no physical damage to the joystick preventing it from returning to the center position. Then turn the power off and back on again (making sure the joystick is not depressed in any direction. If the joystick repeats this error, the controler much be replaced. smithrmrm70@hotmail.com

Posted on Sep 07, 2009

  • 347 Answers

SOURCE: I am painting and turned

hello,please rate me as in 1 to 4 thumbs up for my answer.im disabled myself & have a scooter.Im sure this Document will give ya all the info you need,download:troubleshooting_2007 SHOPRIDER.pdf
do that on the Adobe Reader,save or better still print & store in a polythene sleeve folder so you can keep for future.Type in your brouser shoprider.com & scroll down till you see the PDF File i have give ya,or visit:www.alldatasheet.com to download it.Hopefully you should be sorted,i know what its like to be without your wheels Colin.

Posted on Aug 16, 2010

  • 104 Answers

SOURCE: how do i reset a jet 7 mobile wheelchair

did you put it in lockout accidentally? try this! turn off chair, press and hold the on button till a beep is heard, push and hold the joystick forward till a beep is heard, then pull back and hold joystick till beep is heard, turn off, and turn on. it should work now?

Posted on Sep 05, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Pronto power chair m51 will not engage


Sorry to read about your problem, 1st make sure the charger is unplugged, then restart, next make sure your free wheel levers located in the back left and right side are pushed into the drive position, if the joystick is scanning back and forth, turn off then on and push the horn button twice. The Joystick maybe flashing at you a code.Count the lights and how many are flashing, this is a flash code that can be looked up your manual that came with every Pronto. Strege Mobility

Sep 07, 2017 | Health & Beauty

1 Answer

Light come on controller no flashing code lights joy stick does not work


The M51 could have the motor clutch levers in the free wheel/push mode and the joystick will not blink if this is the case. Make sure that the chair cannot be pushed. If it can be pushed it means it is in free wheel and you need to lock the motors in gear.

If it is in gear and the joysticks green light does not change color or blink it could be that the joystick is bad. When nothing happens and the lights don't blink when you push the joystick knob the chairs controller basically isn't recognizing the joystick movement.
Time to have the joystick repaired or more. Have a technician look at it.

Jun 16, 2015 | Invacare Pronto M51 Power Wheelchair

1 Answer

I get error code 9, what do I do to fix this


Error Code 9 is a "Communications Error". The controller, or "Little black box" down inside the chair is not talking to the joystick, etc. First, check all the connections. Unplug, examine and clean all of the connections going into the controller, and the joystick connection too. Inspect all of the cables for damage to the wiring. If all looks good, then you likely have a bad controller....ouch. These are very expensive to replace new. You might be able to find a used one on Ebay, etc., or you could be better off looking on sites like Craigslist for a complete powerchair replacement. I have found near-new chairs for under a thousand dollars. Search for Pride Jazzy chairs too...a lot more of those for sale than Invacare chairs. Good luck.

Jun 13, 2014 | Invacare Pronto M51 Power Wheelchair

1 Answer

What does 7 times flashing mean is wrong on pronto m91


Hello,

Seven blinks is most often the joystick. A Invacare Remote Programmer can be plugged in to the joystick to verify this.

May 28, 2014 | Electric Mobility Invacare Pronto M41...

1 Answer

I have a pronto m51 wheel chair got the joy stick wet it flashes 7 times how can i fixs it


Here's your M51 manual:
http://www.invacare.com/doc_files/1125085J.pdf
Trouble codes start at p25.
Also, Invacare is proud of the M51's wet-weather performance (check the "Rain Test" chapter in the manual. You might have a warranty issue. Check with an Invacare dealer.

May 06, 2014 | Jet 3 Ultra Power Chair

1 Answer

Yellow light blinks 9 times and chair won't move. how do i fix it?


The problem is bad communication between the joystick and the conroller or power module. By replacing the jostick cables you will see if that fixes the problem. Check with your provider (where you got your chair) to see if they have an extra joystick cable or can loan you one from a chair that they might have. Now there are 2 cables one from the joystick to the base of the chair and one from the base to the controller either could be bad but try the one to the joystick first Hope this helps

May 03, 2011 | Invacare Pronto M51 Power Wheelchair

1 Answer

My pronto m51 sure step service light is flashing seven time and it will only turn to the right


sarah check the joystick cable try unplugging it from the rear of the joystick and plugging it back in then unplug it at the back of the chair and plug it back then turn the chair on to see if you are still getting 7 flashes. If you are then you have one of 2 problems the joystick cable somehow is bad or the joystick itself has got a problem try the cables first to see if it fixes the problem If Medicare paid for the chair then they will pay for most of the repair Contact Roadrunner Mobility @ 1-800-467-2668 Hope this helps you

Apr 02, 2011 | Invacare Health & Beauty

1 Answer

Pronto M51 was plugged in and was turned on to use. The chair never moved and their were sparks from the joystick. Now the chair will not work. What can i do to fix this problem?


Power chairs are not designed to operate while they are plugged into the charger, as it will drag the charger around or you may run over the cord, therefore most power chairs have an inhibit feature that prevents the power chair from moving while it is connected to the charger.
If you saw sparks from the joystick, something has shorted out the controller; moisture or condensation may have gotten into the controller or there may have been a manufacturing defect.
I do not think there is anything you can do at this point except to contact the manufacturer or the place where you purchased the power chair to arrange a service call and replacement of the joystick/controller. If your insurance bought the power chair for you they may cover the repair if it is not covered by the warranty.
Good luck!

Dec 19, 2010 | Invacare Pronto M51 Power Wheelchair

1 Answer

The charge indicator lights flash left to right..when moving joystick the chair does not move.


chair is locked out. turn on then push joystick forward till it beeps then pull backward till it beeps then it is unlocked

Jun 15, 2010 | Invacare Pronto M51 Power Wheelchair

Not finding what you are looking for?
Jet 3 Ultra Power Chair Logo

Related Topics:

35 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jet Health & Beauty Experts

Colin Taylor

Level 2 Expert

347 Answers

wcdoc1953
wcdoc1953

Level 2 Expert

280 Answers

Louis Smith

Level 2 Expert

104 Answers

Are you a Jet Health and Beauty Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...